검색결과
-
[특집-ISO/IEC JTC 1/SC 17 활동] 35. Result of voting on SR Ballot for ISO/IEC 7811-7(N 7345)2023년 12월04일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Result of voting on SR ballot for ISO/IEC 7811-7(N 7345)' 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서인 'Result of voting on SR ballot for ISO/IEC 7811-7'은 ISO/IEC 7811-7:2018 (Ed 3)(restricted access)와 관련한 투표결과를 포함하고 있다.ISO/IEC 7811-7:2018 (Ed 3)(restricted access)는 Identification cards — Recording technique — Part 7: Magnetic stripe: High coercivity, high density에 관한 것이다.N 7345 문서는 N 7338, N 7339, N 7340, N 7341, N 7342, N 7343, N 7344 문서와 마찬가지로 2023년 7월15일~12월2일 동안 투표가 진행됐다. 기간 내 각 회원국들은 안건에 대해 의사를 표명했다.투표 항목은 △Confirm △Revise/Amend △Withdraw △Abstain lack of consensus △Abstain lack of national expert input △Stabilize △Q.2 △Q.3 △Q.4 △Q.5 △Q.6 등 총 11개다. 구체적인 질문 내용은 다음과 같다.▷ Q.1 Recommended action▷ Q.2 Has this International Standard been adopted or is it intended to be adopted in the future as a national standard or other publication?▷ Q.3 Is the national publication identical to the International Standard or was it modified?▷ Q.4 If this International Standard has not been nationally adopted, is it applied or used in your country without national adoption or are products/processes/services used in your country based on this standard?▷ Q.5 Is this International Standard, or its national adoption, referenced in regulations in your country?▷ Q.6 If the committee decides to revise or amend, do you propose an expert and/or project leader for the development of that project?참고로 11개 항목 중 투표 결과를 살펴보면 △Confirm 12개국 △Revise/Amend 1개국 △Abstain lack of national expert input 22개국 등으로 나타났다.- 이하 생략 -
-
[특집-ISO/IEC JTC 1/SC 17 활동] 34. Result of voting on SR ballot for ISO/IEC 7811-6(N 7344)2023년 12월04일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Result of voting on SR ballot for ISO/IEC 7811-6(N 7344)' 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서인 'Result of voting on SR ballot for ISO/IEC 7811-6'은 ISO/IEC 7811-6:2018 (Ed 5)(restricted access)와 관련한 투표결과를 포함하고 있다.ISO/IEC 7811-6:2018 (Ed 5)(restricted access)는 Identification cards — Recording technique — Part 6: Magnetic stripe: High coercivity에 관한 것이다.N 7344 문서는 N 7338, N 7339, N 7340, N 7341, N 7342, N 7343 문서와 마찬가지로 2023년 7월15일~12월2일 동안 투표가 진행됐다. 기간 내 각 회원국들은 안건에 대해 의사를 표명했다.투표 항목은 △Confirm △Revise/Amend △Withdraw △Abstain lack of consensus △Abstain lack of national expert input △Stabilize △Q.2 △Q.3 △Q.4 △Q.5 △Q.6 등 총 11개다. 구체적인 질문 내용은 다음과 같다.▷ Q.1 Recommended action▷ Q.2 Has this International Standard been adopted or is it intended to be adopted in the future as a national standard or other publication?▷ Q.3 Is the national publication identical to the International Standard or was it modified?▷ Q.4 If this International Standard has not been nationally adopted, is it applied or used in your country without national adoption or are products/processes/services used in your country based on this standard?▷ Q.5 Is this International Standard, or its national adoption, referenced in regulations in your country?▷ Q.6 If the committee decides to revise or amend, do you propose an expert and/or project leader for the development of that project?참고로 11개 항목 중 투표 결과를 살펴보면 △Confirm 11개국 △Revise/Amend 1개국 △Abstain lack of national expert input 23개국 등으로 나타났다.- 이하 생략 -
-
[특집-ISO/IEC JTC 1/SC 17 활동] 33. Result of voting on SR ballot for ISO/IEC 7811-2(N 7343)2023년 12월04일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Result of voting on SR ballot for ISO/IEC 7811-2(N 7343)' 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서인 'Result of voting on SR ballot for ISO/IEC 7811-2'는 ISO/IEC 7811-2:2018 (Ed 5)(restricted access)와 관련한 투표결과를 포함하고 있다. ISO/IEC 7811-2:2018 (Ed 5)(restricted access)는 Identification cards — Recording technique — Part 2: Magnetic stripe: Low coercivity에 관한 것이다. N 7343 문서는 N 7338, N 7339, N 7340, N 7341, N 7342 문서와 마찬가지로 2023년 7월15일~12월2일 동안 투표가 진행됐다. 기간 내 각 회원국들은 안건에 대해 의사를 표명했다.투표 항목은 △Confirm △Revise/Amend △Withdraw △Abstain lack of consensus △Abstain lack of national expert input △Stabilize △Q.2 △Q.3 △Q.4 △Q.5 △Q.6 등 총 11개다. 구체적인 질문 내용은 다음과 같다.▷ Q.1 Recommended action▷ Q.2 Has this International Standard been adopted or is it intended to be adopted in the future as a national standard or other publication?▷ Q.3 Is the national publication identical to the International Standard or was it modified?▷ Q.4 If this International Standard has not been nationally adopted, is it applied or used in your country without national adoption or are products/processes/services used in your country based on this standard?▷ Q.5 Is this International Standard, or its national adoption, referenced in regulations in your country?▷ Q.6 If the committee decides to revise or amend, do you propose an expert and/or project leader for the development of that project?참고로 11개 항목 중 투표 결과를 살펴보면 △Confirm 12개국 △Revise/Amend 1개국 △Abstain lack of consensus 1개국 △Abstain lack of national expert input 21개국 등으로 나타났다. - 이하 생략 -
-
[특집-ISO/IEC JTC 1/SC 17 활동] 32. Result of voting on SR Ballot for ISO/IEC 7811-1(N 7342)2023년 12월04일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Result of voting on SR Ballot for ISO/IEC 7811-1(N 7342)' 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서인 'Result of voting on SR Ballot for ISO/IEC 7811-1'는 ISO/IEC 7811-1:2018 (Ed 5)(restricted access)와 관련한 투표결과를 포함하고 있다. ISO/IEC 7811-1:2018 (Ed 5)(restricted access)는 Identification cards — Recording technique — Part 1: Embossing에 관한 것이다. N 7342 문서는 N 7338, N 7339, N 7340, N 7341 문서와 마찬가지로 2023년 7월15일~12월2일 동안 투표가 진행됐다. 기간 내 각 회원국들은 안건에 대해 의사를 표명했다.투표 항목은 △Confirm △Revise/Amend △Withdraw △Abstain lack of consensus △Abstain lack of national expert input △Stabilize △Q.2 △Q.3 △Q.4 △Q.5 △Q.6 등 총 11개다. 구체적인 질문 내용은 다음과 같다.▷ Q.1 Recommended action▷ Q.2 Has this International Standard been adopted or is it intended to be adopted in the future as a national standard or other publication?▷ Q.3 Is the national publication identical to the International Standard or was it modified?▷ Q.4 If this International Standard has not been nationally adopted, is it applied or used in your country without national adoption or are products/processes/services used in your country based on this standard?▷ Q.5 Is this International Standard, or its national adoption, referenced in regulations in your country?▷ Q.6 If the committee decides to revise or amend, do you propose an expert and/or project leader for the development of that project?참고로 11개 항목 중 투표 결과를 살펴보면 △Confirm 12개국 △Revise/Amend 1개국 △Abstain lack of consensus 1개국 △Abstain lack of national expert input 21개국 등으로 나타났다. - 이하 생략 -
-
[특집-ISO/IEC JTC 1/SC 17 활동] 31. Result of voting on SR Ballot for ISO/IEC 18745-1(N 7341)2023년 12월04일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Result of voting on SR Ballot for ISO/IEC 18013-1(N 7340)' 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서인 'Result of voting on SR Ballot for ISO/IEC 18745-1'는 ISO/IEC 18745-1:2018 (Ed 2)(restricted access)와 관련한 투표결과를 포함하고 있다. ISO/IEC 18745-1:2018 (Ed 2)(restricted access)는 Test methods for machine readable travel documents (MRTD) and associated devices — Part 1: Physical test methods for passport books (durability)에 관한 것이다. N 7341 문서는 N 7338, N 7339, N 7340 문서와 마찬가지로 2023년 7월15일~12월2일 동안 투표가 진행됐다. 기간 내 각 회원국들은 안건에 대해 의사를 표명했다.투표 항목은 △Confirm △Revise/Amend △Withdraw △Abstain lack of consensus △Abstain lack of national expert input △Stabilize △Q.2 △Q.3 △Q.4 △Q.5 △Q.6 등 총 11개다. 구체적인 질문 내용은 다음과 같다.▷ Q.1 Recommended action▷ Q.2 Has this International Standard been adopted or is it intended to be adopted in the future as a national standard or other publication?▷ Q.3 Is the national publication identical to the International Standard or was it modified?▷ Q.4 If this International Standard has not been nationally adopted, is it applied or used in your country without national adoption or are products/processes/services used in your country based on this standard?▷ Q.5 Is this International Standard, or its national adoption, referenced in regulations in your country?▷ Q.6 If the committee decides to revise or amend, do you propose an expert and/or project leader for the development of that project?참고로 11개 항목 중 투표 결과를 살펴보면 △Confirm 9개국 △Revise/Amend 4개국 △Abstain lack of national expert input 22개국 등으로 나타났다. - 이하 생략 -
-
[특집-기술위원회] TC 215 - 의료 정보학(Health informatics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 △1996년 TC 213, TC 214 등이 있다.ISO/TC 215 의료 정보학(Health informatics)과 관련된 기술위원회는 1998년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 레이첼 호손(Ms Rachel Hawthorne)가 책임지고 있다. 현재 의장은 토드 쿠퍼(Mr Todd Cooper)이며 임기는 2026년 말까지다. ISO 기술 프로그램 관리자는 마호 다카하시(Mme Maho Takahashi), ISO 편집 관리자는 발레리아 아가넨노네(Ms Valeria Agamennone) 등이다.범위는 의료 관련 데이터, 의료 시스템의 모든 측면을 지원하고 활성화하는 지식의 수집, 교환 및 사용을 촉진하기 위한 의료 정보학 분야의 표준화다.현재 ISO/TC 215 사무국과 관련해 발행된 표준은 237개며 ISO/TC 215 사무국의 직접적인 책임 하에 발행된 표준은 225개다.ISO/TC 215과 관련해 개발 중인 표준은 64개며 이중 ISO/TC 215 사무국의 직접적인 책임 하에 개발 중인 표준은 62개다. 참여하고 있는 회원은 35개국, 참관 회원은 32개국이다.□ ISO/TC 215 사무국의 직접적인 책임 하에 발행된 표준 225개 중 15개 목록▷ISO 1828:2012 Health informatics — Categorial structure for terminological systems of surgical procedures▷ISO/TR 4421:2023 Health informatics — Introduction to Ayurveda informatics▷ISO/TS 5044:2023 Health informatics — Information model for quality control of traditional Chinese medicinal products▷ISO/TS 5118:2022 Health informatics — Categorial structure of representation for evaluation of clinical practice guidelines of traditional Chinese medicine▷ISO/TS 5346:2022 Health informatics — Categorial structure for representation of traditional Chinese medicine clinical decision support system▷ISO 5477:2023 Health informatics — Interoperability of public health emergency preparedness and response information systems▷ISO/TS 5499:2024 Health informatics — Clinical particulars — Core principles for the harmonization of therapeutic indications terms and identifiers▷ISO/TS 5568:2022 Health informatics — Traditional Chinese medicine — Labelling metadata of human biological sample information▷ISO/TS 5569:2023 Health informatics — Conceptual data model for Chinese medicinal herbs▷ISO/TR 9143:2023 Health informatics — Sex and gender in electronic health records▷ISO 10159:2011 Health informatics — Messages and communication — Web access reference manifest▷ISO 10781:2023 Health informatics — HL7 Electronic Health Record-System Functional Model, Release 2.1 (EHR FM)▷ISO/IEEE 11073-00103:2015 Health informatics — Personal health device communication — Part 00103: Overview▷ISO/IEEE 11073-10101:2020 Health informatics — Device interoperability — Part 10101: Point-of-care medical device communication — Nomenclature▷ISO/IEEE 11073-10102:2014 Health informatics — Point-of-care medical device communication — Part 10102: Nomenclature — Annotated ECG□ ISO/TC 215 사무국의 직접적인 책임 하에 개발 중인 표준 62개 중 15개 목록▷ISO/AWI TR 4419 Health informatics — Reducing clinicians burden▷ISO/DTS 5384 Health informatics - Categorial Structure and Data Elements for the Identification and Exchange of Immunization Data▷ISO/CD TS 5615 Health informatics — Accelerating Safe, Effective and Secure Remote Connected Care and Mobile Health Through Standards-Based Interoperability Solutions Addressing Gaps Revealed by Pandemics▷ISO/DTS 5777 Health informatics — The architecture of internet healthcare service network▷ISO/DTS 5788 Health informatics — Internet healthcare service pattern▷ISO/CD TS 6201.2 Health Informatics — Personalized Digital Health -Framework▷ISO/CD TS 6204 Health Informatics — Categorial structures for representation of Ayurvedic medicinal water — Decocting process in Ayurveda▷ISO/AWI TS 6226 Health informatics — Reference architecture for syndromic surveillance systems for infectious diseases▷ISO/DTR 6231 Health informatics — Standardizing graphical content▷ISO/CD TS 6268-1 Health informatics — Cybersecurity framework for telehealth environments — Part 1: Overview and Concepts▷ISO/AWI TS 6268-2 Health informatics — Cybersecurity framework for telehealth environments — Part 2: Cybersecurity reference models of telehealth▷ISO/CD TS 7122 Health Informatics — Guidelines for exchanging data generated by POCT (Point of Care Testing) devices between screening center and clinical laboratory▷ISO/AWI TS 9166 Health Informatics — Guidelines for self-assessment questionnaire systems▷ISO/DTS 9320 Health informatics — Standardized data set for transfer of hemodialysis patients▷ISO/DTS 9321 Health informatics — General requirements of multi-centre medical data collaborative analysis□ ISO/TC 215 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 215/SC 1 Genomics Informatics ; 발행된 표준 12개, 개발 중인 표준 2개
-
[특집-기술위원회] TC 214 - 승강기 작업 플랫폼(Elevating work platforms)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 등이 있다.ISO/TC 214 승강기 작업 플랫폼(Elevating work platforms)과 관련된 기술위원회는 TC 213과 마찬가지로 1996년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 샐리 사이츠(Ms Sally Seitz)가 책임지고 있다. 현재 의장은 스티븐 A. 베스트(Mr Stephen A. Best)이며 임기는 2029년 말까지다. ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 앤 기엣(Ms Anne Guiet) 등이다.범위는 용어, 등급, 일반 원칙(기술적 성능 요구 사항 및 위험 평가), 안전 요구사항, 테스트 방법, 유지관리, 승강에 사용되는 작업 플랫폼을 올리기 위한 조작 등의 표준화다. 또한 작업을 수행할 작업 위치에 직원(및 관련 작업 도구, 자재 등)을 배치에 대한 표준화도 포함된다.현재 ISO/TC 214 사무국의 직접적인 책임 하에 발행된 표준은 9개며 ISO/TC 214 사무국의 직접적인 책임 하에 개발 중인 표준은 3개다. 참여하고 있는 회원은 19개국, 참관 회원은 19개국이다.□ ISO/TC 214 사무국의 직접적인 책임 하에 발행된 표준 9개 목록▷ISO 16368:2010 Mobile elevating work platforms — Design, calculations, safety requirements and test methods▷ISO 16369:2007 Elevating work platforms — Mast-climbing work platforms▷ISO 16653-1:2008 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 1: MEWPs with retractable guardrail systems▷ISO 16653-2:2021 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 2: MEWPs with non-conductive (insulating) components▷ISO 16653-3:2011 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 3: MEWPs for orchard operations▷ISO 18878:2013 Mobile elevating work platforms — Operator (driver) training▷ISO 18893:2014 Mobile elevating work platforms — Safety principles, inspection, maintenance and operation▷ISO 20381:2009 Mobile elevating work platforms — Symbols for operator controls and other displays▷ISO 21455:2020 Mobile elevating work platforms — Operator's controls — Actuation, displacement, location and method of operation□ ISO/TC 214 사무국의 직접적인 책임 하에 개발 중인 표준 3개 목록▷ISO/FDIS 16368 Mobile elevating work platforms — Design, calculations, safety requirements and test methods▷ISO/DIS 18878 Mobile elevating work platforms — Operator (driver) training▷ISO/DIS 18893 Mobile elevating work platforms — Safety principles, inspection, maintenance and operation
-
[특집-기술위원회] TC 213 - 치수와 기하학적 제품의 사양 및 검증(Dimensional and geometrical product specifications and verification)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 등이 있다.ISO/TC 213 치수와 기하학적 제품의 사양 및 검증(Dimensional and geometrical product specifications and verification)과 관련된 기술위원회는 1996년 결성됐다. 사무국은 영국 표준협회(British Standards Institution, BSI)에서 맡고 있다.위원회는사라 켈리(Miss Sarah Kelly)가 책임지고 있다. 현재 의장은 이안 맥클라우드(Mr Iain Macleod)이며 임기는 2025년말까지다. ISO 기술 프로그램 관리자는 이사벨 베가(Ms Isabelle Vega), ISO 편집 관리자는 니콜라 페루(Ms Nicola Perou) 등이다.범위는 기하학적 제품 사양(GPS) 분야의 표준화다. 즉 치수 및 기하학적 공차, 표면 특성 및 관련 검증 원리, 치수 및 기하학적 측정의 불확실성을 포함한 측정 장비 및 교정 요구 사항을 다루는 거시 및 미세 형상 사양이다.표준화에는 기본 레이아웃과 도면 표시(기호)에 대한 설명이 포함된다. 단, 도면 표시(기호)의 특정 비율 및 치수 정의, 실행은 제외된다.현재 ISO/TC 213 사무국의 직접적인 책임 하에 발행된 표준은 147개며 ISO/TC 213 사무국의 직접적인 책임 하에 개발 중인 표준은 22개다. 참여하고 있는 회원은 26개국, 참관 회원은 25개국이다.□ ISO/TC 213 사무국의 직접적인 책임 하에 발행된 표준 147개 중 15개 목록▷ISO 1:2022 Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties▷ISO 286-1:2010 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits▷ISO 286-1:2010/Cor 1:2013 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits — Technical Corrigendum 1▷ISO 286-2:2010 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts▷ISO 286-2:2010/Cor 1:2013 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts — Technical Corrigendum 1▷ISO 463:2006 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges▷ISO 463:2006/Cor 1:2007 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 1▷ISO 463:2006/Cor 2:2009 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 2▷ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out▷ISO 1119:2011 Geometrical product specifications (GPS) — Series of conical tapers and taper angles▷ISO 1660:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing▷ISO 1938-1:2015 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size▷ISO 1938-2:2017 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Reference disk gauges▷ISO 2538-1:2014 Geometrical product specifications (GPS) — Wedges — Part 1: Series of angles and slopes▷ISO 2538-2:2014 Geometrical product specifications (GPS) — Wedges — Part 2: Dimensioning and tolerancing□ ISO/TC 213 사무국의 직접적인 책임 하에 개발 중인 표준 22개 중 15개 목록▷ISO/CD 1938-1 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size▷ISO/AWI 2768 General tolerances▷ISO/DIS 5059-1 Geometrical product specifications (GPS) — Dimensional measuring equipment: inside micrometers — Part 1: Two-point inside micrometers — Design and metrological characteristics▷ISO/FDIS 5459 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems▷ISO/DIS 5463 Geometrical product specifications (GPS) — Form measuring equipment; Rotary axis form measuring instruments — Design and metrological characteristics▷ISO/CD 10360-102 Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 102: The language of symbols G3▷ISO/AWI 12179 Geometrical product specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments▷ISO/DIS 14405-1 Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes▷ISO/CD TS 15530-2 Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 2: Part 2: Evaluating task-specific measurement uncertainty by multiple measurement strategies using a single uncalibrated workpiece▷ISO/DIS 16610-21 Geometrical product specifications (GPS) — Filtration — Part 21: Linear profile filters: Gaussian filters▷ISO/CD 16610-22 Geometrical product specifications (GPS) — Filtration — Part 22: Linear profile filters: Spline filters▷ISO/DIS 16610-31 Geometrical product specifications (GPS) — Filtration — Part 31: Robust profile filters: Gaussian regression filters▷ISO/DIS 16610-45 Geometrical product specifications (GPS) — Filtration — Part 45: Morphological profile filters: Segmentation▷ISO 18183-1 Geometrical product specifications (GPS) — Partition — Part 1: Vocabulary and basic concepts▷ISO/CD TR 23850 Geometrical product specifications (GPS) — Association — Mathematical concepts
-
[특집-기술위원회] TC 212 - 의료 실험실 및 체외 진단 시스템(Medical laboratories and in vitro diagnostic systems)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 등이 있다.ISO/TC 212 의료 실험실 및 체외 진단 시스템(Medical laboratories and in vitro diagnostic systems)과 관련된 기술위원회는 TC 210, TC 211과 마찬가지로 1994년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는데이비드 스테리(Mr David Sterry)가 책임지고 있다. 현재 의장은 헤수스 루에다 로드리게스(Mr Jesus Rueda Rodriguez)이며 임기는 2027년말까지다. ISO 기술 프로그램 관리자는 이사벨 베가(Ms Isabelle Vega), ISO 편집 관리자는 발레리아 아가넨노네(Ms Valeria Agamennone) 등이다.범위는 의료 실험실 및 체외 진단 시스템 분야의 표준화 및 지침이다. 여기에는 품질 관리, 분석 전후 절차, 분석 성능, 실험실 안전, 참조 시스템 및 품질 보증 등이 포함된다.단, ISO/TC 176에서 다루는 일반 품질 관리 표준, ISO/TC 210에서 다루는 의료기기 품질 관리 표준, ISO/TC 334 참조 자료 위원회(REMCO)에서 다루는 참조 자료 지침, ISO 적합성 평가 위원회(CASCO)에서 다루는 적합성 평가 지침 등은 제외된다현재 ISO/TC 212 사무국의 직접적인 책임 하에 발행된 표준은 47개며 ISO/TC 212 사무국의 직접적인 책임 하에 개발 중인 표준은 23개다. 참여하고 있는 회원은 41개국, 참관 회원은 33개국이다.□ ISO/TC 212 사무국의 직접적인 책임 하에 발행된 표준 47개 중 15개 목록▷ISO 4307:2021 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for saliva — Isolated human DNA▷ISO/TS 5798:2022 In vitro diagnostic test systems — Requirements and recommendations for detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) by nucleic acid amplification methods▷ISO 15189:2022 Medical laboratories — Requirements for quality and competence▷ISO 15190:2020 Medical laboratories — Requirements for safety▷ISO 15193:2009 In vitro diagnostic medical devices — Measurement of quantities in samples of biological origin — Requirements for content and presentation of reference measurement procedures▷ISO 15194:2009 In vitro diagnostic medical devices — Measurement of quantities in samples of biological origin — Requirements for certified reference materials and the content of supporting documentation▷ISO 15195:2018 Laboratory medicine — Requirements for the competence of calibration laboratories using reference measurement procedures▷ISO 15197:2013 In vitro diagnostic test systems — Requirements for blood-glucose monitoring systems for self-testing in managing diabetes mellitus▷ISO 15198:2004 Clinical laboratory medicine — In vitro diagnostic medical devices — Validation of user quality control procedures by the manufacturer▷ISO 16256:2021 Clinical laboratory testing and in vitro diagnostic test systems — Broth micro-dilution reference method for testing the in vitro activity of antimicrobial agents against yeast fungi involved in infectious diseases▷ISO/TS 16782:2016 Clinical laboratory testing — Criteria for acceptable lots of dehydrated Mueller-Hinton agar and broth for antimicrobial susceptibility testing▷ISO 17511:2020 In vitro diagnostic medical devices — Requirements for establishing metrological traceability of values assigned to calibrators, trueness control materials and human samples▷ISO/TS 17518:2015 Medical laboratories — Reagents for staining biological material — Guidance for users▷ISO 17593:2022 Clinical laboratory testing and in vitro medical devices — Requirements for in vitro monitoring systems for self-testing of oral anticoagulant therapy▷ISO 17822:2020 In vitro diagnostic test systems — Nucleic acid amplification-based examination procedures for detection and identification of microbial pathogens — Laboratory quality practice guide□ ISO/TC 212 사무국의 직접적인 책임 하에 개발 중인 표준 23개 중 15개 목록▷ISO/DTS 5441 Competence requirements for biorisk management advisors▷ISO/DIS 5649 Medical laboratories — Concepts and specifications for the design, development, implementation, and use of laboratory-developed tests▷ISO/AWI TS 7446 ISO 35001 — Biorisk management for laboratories and other related organisations — Implementation guidance▷ISO/CD TS 7552-1 Specifications for pre-examination processes for circulating tumor cells (CTCs) in venous whole blood — Part 1: Isolated RNA▷ISO/CD TS 7552-2 Specifications for pre-examination processes for circulating tumor cells (CTCs) in venous whole blood — Part 2: Isolated DNA▷ISO/CD TS 7552-3 Specifications for pre-examination processes for circulating tumor cells (CTCs) in venous whole blood — Part 3: Preparations for analytical CTC staining▷ISO/AWI TS 8219 Sequencing and clinical application to infectious diseases▷ISO/DIS 15193 In vitro diagnostic medical devices — Requirements for reference measurement procedures▷ISO/DIS 15194 In vitro diagnostic medical devices — Requirements for certified reference materials and the content of supporting documentation▷ISO/CD TS 16766.2 Manufacturers’considerations for in vitro diagnostic medical devices in a public health crisis▷ISO/AWI TS 18701 Molecular in vitro diagnostic examinations — Specificationsfor pre-examination processes for human specimens — Isolated microbiome DNA▷ISO/AWI TS 18702 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for exosomes and other extracellular vesicles in venous whole blood — DNA, RNA and proteins▷ISO/AWI 18703 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for venous whole blood — Isolated circulating cell free RNA from plasma▷ISO/CD 18704 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for urine and other body fluids — Isolated cell free DNA▷ISO/DIS 21474-3 In vitro diagnostic medical devices — Multiplex molecular testing for nucleic acids — Part 3: Interpretation and reports
-
[특집-기술위원회] TC 211 - 지리정보/지리학(Geographic information/Geomatics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 등이 있다.ISO/TC 211지리정보/지리학(Geographic information/Geomatics)과 관련된 기술위원회는 TC 210과 마찬가지로 1994년 결성됐다. 사무국은 스웨덴 국립표준청(Svenska institutet för standarder, SIS)에서 맡고 있다.위원회는 마츠 올린(Mr Mats Åhlin)가 책임지고 있다. 현재 의장은 피터 파슬로(Mr Peter Parslow)이며 임기는 2024년말까지다. ISO 기술 프로그램 관리자는 하킴 음킨시(Mr Hakim Mkinsi), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등이다.범위는 디지털 지리정보 분야의 표준화다. 지구와 관련된 위치와 직간접적으로 연관된 물체나 현상에 관한 정보에 대한 구조화된 표준 세트 확립을 목표로 하고 있다.지리 정보의 범위 내에서 이러한 표준은 데이터 관리를 위한 방법, 도구 및 서비스를 지정할 수 있다. 데이터 관리는 사용자 및 시스템을 위한 데이터 획득, 처리, 분석, 접근, 제시 및 출판이 포함된다.이 작업은 가능한 경우 정보 기술 및 데이터에 대한 적절한 표준과 연결되어야 하며 지리 데이터를 사용하는 부문별 응용 프로그램 개발을 위한 프레임워크를 제공해야 된다.현재 ISO/TC 211 사무국의 직접적인 책임 하에 발행된 표준은 97개며 ISO/TC 211 사무국의 직접적인 책임 하에 개발 중인 표준은 26개다. 참여하고 있는 회원은 38개국, 참관 회원은 35개국이다.□ ISO/TC 211 사무국의 직접적인 책임 하에 발행된 표준 97개 중 15개 목록▷ISO 6709:2022 Standard representation of geographic point location by coordinates▷ISO 19101-1:2014 Geographic information — Reference model — Part 1: Fundamentals▷ISO 19101-2:2018 Geographic information — Reference model — Part 2: Imagery▷ISO 19103:2015 Geographic information — Conceptual schema language▷ISO 19104:2016 Geographic information — Terminology▷ISO 19105:2022 Geographic information — Conformance and testing▷ISO 19106:2004 Geographic information — Profiles▷ISO 19107:2019 Geographic information — Spatial schema▷ISO 19108:2002 Geographic information — Temporal schema▷ISO 19108:2002/Cor 1:2006 Geographic information — Temporal schema — Technical Corrigendum 1▷ISO 19109:2015 Geographic information — Rules for application schema▷ISO 19110:2016 Geographic information — Methodology for feature cataloguing▷ISO 19111:2019 Geographic information — Referencing by coordinates▷ISO 19111:2019/Amd 1:2021 Geographic information — Referencing by coordinates — Amendment 1▷ISO 19111:2019/Amd 2:2023 Geographic information — Referencing by coordinates — Amendment 2□ ISO/TC 211 사무국의 직접적인 책임 하에 개발 중인 표준 26개 중 15개 목록▷ISO/DIS 19103 Geographic information — Conceptual schema language▷ISO/CD 19109 Geographic information — General feature model and rules for application schema▷ISO/AWI TR 19115-4 Geographic information – Metadata — Part 4: JSON schema implementation of metadata fundamentals▷ISO/DIS 19116 Geographic information — Positioning services▷ISO/AWI TR 19121 Geographic information — Imagery and gridded data▷ISO/AWI 19123-2 Geographic information — Schema for coverage geometry and functions — Part 2: Coverage implementation schema▷ISO/AWI TS 19123-4 Geographic information — Schema for coverage geometry and functions — Part 4: Tiling Schema▷ISO/AWI TS 19124-2 Geographic information — Calibration and validation of remote sensing data and derived products — Part 2: SAR▷ISO/AWI 19127 Geographic information — Geodetic register▷ISO/AWI TS 19130-2 Geographic information — Imagery sensor models for geopositioning — Part 2: SAR, InSAR, lidar and sonar▷ISO/CD 19135 Geographic information registration — Requirements▷ISO/DTS 19144-3 Geographic information — Classification systems — Part 3: Land Use Meta Language (LUML)▷ISO/DIS 19152-2 Geographic information — Land Administration Domain Model (LADM) — Part 2: Land registration▷ISO/FDIS 19152-3 Geographic information — Land Administration Domain Model (LADM) — Part 3: Marine georegulation▷ISO/DIS 19152-4 Geographic information — Land Administration Domain Model (LADM) — Part 4: Valuation information