검색결과
-
TTA, 자율주행차 협력주행 국제표준화 주도한국정보통신기술협회(회장 손승현, 이하 TTA)에 따르면 ‘24년 4월 15일부터 26일까지 프랑스 렌에서 개최된 ITU-T SG16(멀티미디어) 국제회의에서 TTA 주도로 제안한 자율주행차 표준화 과제가 채택됐다. 이번에 채택된 과제는 '커넥티드 자율주행차를 위한 협력적 주행환경 인식 프레임워크 및 요구사항'(F.CAV-CDP, 에디터 TTA 김영재 박사, 고정욱 선임)이다. F.CAV-CDP는 통신 기술과 센싱 기술을 융합한 차세대 모빌리티 기술이다. 채택된 자율주행차 표준화 과제는 향후 2년간 지속 개발을 통해 ‘26년까지 ITU-T SG16(멀티미디어) 최종 승인을 목표로 하고 있으며 국내 기업의 mmWave 활용 기술에 대한 표준특허 확보도 추진할 계획이다. 제안이 표준화된다면 커넥티드 자율주행차량(CAV)과 노변 장치(RSU) 간 센싱 (sensing) 데이터 공유 및 듀얼 채널 통신(5.9GHZ, mmWave)을 활용하여 도로 주행환경을 빠르게 인지하여 더욱 안전한 자율주행 서비스가 가능하리라 기대된다. 또한 TTA는 ETRI, 벤처기업 Arklink 및 에스와이피(SYP) 특허법인과 ‘23년부터 협력해 ’자율주행기술개발혁신사업*‘의 과제를 수행하고 있다. 자율주행기술개발혁신사업은 과학기술정보통신부, 산업통상자원부, 국토교통부, 경찰청 등 4개 부처가 추진하는 자율주행차 핵심 국제표준 및 특허 선도기술 연구를 위한 다부처 협업사업(’21~‘27)이다. TTA 손승현 회장은 “자율주행 기술은 개발의 난이도가 높아 상업화에 더딘 면이 있지만, 이동과 수송의 혁신을 가능케 하는 기술로 산업적 중요도가 매우 크다”라고 평가하면서 “지속적으로 자율주행 분야 표준화 활동을 강화 하겠다”고 밝혔다. 표준화과제 F.CAV-CDP에 대한 주요 내용은 TTA 홈페이지를 확인하면 된다.
-
3GPP, 새로운 6G 로고 확정, 표준화 마일스톤 발표한국정보통신기술협회(회장 손승현, 이하 TTA)에 따르면 제52차 3GPP PCG(Project Co-ordination Group, 정책 조정위원회) 및 제51차 OP(Organizational Partners, 운영기관) 국제회의에서 3GPP 6G 로고가 확정됐다. 제52차 3GPP PCG 및 제51차 OP 국제회의는 4월 23일부터 24일까지 양일간 미국 레스턴에서 개최됐다. 참고로 3GPP는 2008년 LTE(Long-Term Evolution) 규격 이후부터 새로운 기술 기능이나 서비스 도입을 기점으로 기술 브랜드와 로고를 개발해 차별화하고 있다. 특히, ’23.12월 TTA를 포함한 운영기관 간 6G 표준화 공동선언문을 발표했으며 ’24.3월 6G 표준화 일정을 수립했다. 이번 회의에서 6G 로고를 발표하면서 3GPP의 6G 표준화 여정을 위한 모든 준비가 완료됐다. 국제 회의에 참가한 TTA 김대중 본부장은 표준정책조정그룹(PCG) 부의장으로서 3GPP의 정책 및 규정 논의에서 중추적인 역할을 수행했으며 삼성전자, LG전자 등 31개 국내 회원사의 이익을 적극적으로 대변했다. 또한 ’26월 10월 예정된 RAN(무선접속망) 산하 작업반 국제회의 유치와 매년 3GPP 주요 국제회의를 유치하는 청사진을 수립했다. 3GPP 의장단 지역별 불균형 해소를 위해 운영기관 기반 의장단 밸런스 유지를 제안했으며 국내 전문가의 3GPP 의장단 진출에 유리한 환경 조성에 기반을 마련했다. TTA 손승현 회장은 “3GPP의 6G 로고 공개로 6G 표준화를 위한 모든 제반 사항이 갖추어졌다" 며, "TTA는 민·관 협력을 통해 ’25년 3월 3GPP 기술총회와 함께 3GPP 6G 기술 워크숍을 개최하고, 매년 3GPP 주요 국제회의를 유치하는 등 명실상부 6G 표준화 주도국으로서의 위상을 강화하겠다”고 밝혔다. 한편 "3GPP 최상위 정책 결정에 있어 국내 회원사들의 영향력을 강화할 수 있도록 3GPP 표준조정위원회에서 역할에 충실할 것이다.”라고 덧붙였다.
-
TTA, 양자 분야 글로벌 표준화 선도한국정보통신기술협회(회장 손승현, 이하 TTA)에 따르면 지난 4월 14일(일요일) 세계 양자의 날(World Quantum Day)을 맞이해 '양자 기술 분야 국제표준화 기구 대응 및 한국 주도 사실표준화 기구 신설을 통한 글로벌 양자기술 국제표준화 선도' 의지를 표명했다. 양자 기술에 대한 국제표준화는 ITU, ETSI, IRTF 등에서 세부 기술 분야별로 추진되었으나, 최근 신설된 ISO와 IEC의 합동기술위원회인 JTC 3(양자기술, 의장국: 한국)를 중심으로 본격적으로 진행될 것으로 예상되기 때문이다. TTA는 지난 20여 년간 국내 산·학·연의 국제표준화 활동지원 프로그램을 운영하고 있는 ICT 표준화 전문기관이다. 따라서 양자통신, 양자암호 등 관련 전문가 10여 명을 확보해 꾸준한 지원을 통해 ITU-T 양자 기술 관련(ITU-T SG11(프로토콜) 3건, SG13(미래 네트워크) 10건, SG17(정보보호) 3건 등) 의장단 3석(27%)을 진출시켰다. 또한 '양자키분배 네트워크 상호연동 보안 요구사항(X.sec_QKDNI)'등 16건(51.6%)이 우리나라 주도로 진행 중이다. 특히, 양자 기술 분야에서 ITU-T 최초의 표준은 우리나라가 제안한 Y.3800(양자키 분배망 개요)*으로 2019년 승인됐다. Y.3800(양자키 분배망 개요)는 ITU-T Y.3800 Overview on networks supporting quantum key distribution이다. 2024년 현재까지 SG11(프로토콜) 5건, SG13(미래 네트워크) 20건, SG17(정보보호) 6건 등 총 31건의 유관 표준이 제정됐다. TTA는 양자기술 시장 표준화 선도 및 양자 ICT 산업화 촉진을 위해 세계 최초로 한국 주도의 '글로벌 사실표준화기구'를 2024년 하반기 출범을 목표로 추진중이다. 양자 분야 글로벌 사실표준화 기수의 명칭은 QINSA(Quantum INformation Standard Association, 이하 QINSA)이며 IBM을 포함해 양자 전문기업 10개가 참여하고, 국내 이동통신 3사(KT, SKT, LGU+) 및 중소기업 등 100여 개 국내외 회원사를 확보했다. QINSA는 작업반(통신, 컴퓨팅, 센서) 통해 표준개발, 유즈케이스·비즈니스 모델을 발굴하며 미국 QED-C, 일본 Q-STAR, 유럽연합 QUIC 등 양자 분야 산업협의체와 다양한 협력을 통해 글로벌 사실표준화기구로서 위상을 제고할 예정이다. TTA 손승현 회장은 '우리나라가 표준을 기반으로 글로벌 시장에서 양자 기술 경쟁력을 강화하고 선도적인 위치를 확보할 수 있도록 양자 기술의 표준화 활동을 지속적으로 확대해 나가겠다'고 밝혔다.
-
[특집-기술위원회] TC 222 - 개인 재무 계획(Personal financial planning)[STANDBY]스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 △1996년 TC 213, TC 214 △1998년 TC 215~218 1999년 TC 219, TC 220 등이 있다.ISO/TC 222 개인 재무 계획(Personal financial planning)[STANDBY]과 관련된 기술위원회는 TC 221과 마찬가지로 2000년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 조세핀 술트(Mrs Josefine Sult)가 책임지고 있으며 현재 의장은 공석이다. ISO 기술 프로그램 관리자는 샐리 스윙우드(Ms Sally Swingewood)이며 ISO 편집 관리자는 크리스틴 라크로아(Mme Christine Lacroix)이다.범위는 교육, 시험, 경험 및 윤리적 행동 요소를 기반으로 한 실무자 인증 표준화를 포함해 개인 재무 계획 분야의 표준화다.또한 고객의 재무 상태 목표, 분석 및 평가, 재무 계획 권장사항 개발 및 제시 등을 포함해 고객/계획자 관계 설정 및 정의, 목표를 포함한 고객 데이터의 수집 등 6가지 요소를 포함된다.이에 국한되지 않는 개인 재무 계획 프로세스 표준화뿐 아니라 대안 및 재무계획 권장 사항 구현과 모니터링 등도 표준화에 포함된다.현재 ISO/TC 222 사무국의 직접적인 책임 하에 발행된 표준은 1개며 ISO/TC 222 사무국의 직접적인 책임 하에 개발 중인 표준은 없다. 참여하고 있는 회원은 12개국, 참관 회원은 18개국이다.□ ISO/TC 222 사무국의 직접적인 책임 하에 발행된 표준1개 목록▷ISO 22222:2005 Personal financial planning — Requirements for personal financial planners
-
[특집-기술위원회] TC 221 - 토목섬유(Geosynthetics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 △1996년 TC 213, TC 214 △1998년 TC 215~218 1999년 TC 219, TC 220 등이 있다.ISO/TC 221 토목섬유(Geosynthetics)와 관련된 기술위원회는 2000년 결성됐다. 사무국은 영국 표준협회(British Standards Institution, BSI)에서 맡고 있다.위원회는 데이비드 하이드 1세(Mr David I Hyde)가 책임지고 있다. 현재 의장은 피터 애치슨(Mr Peter Atchison)이며 임기는 2026년 말까지다.ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 타이나 비셰비치(Ms Tajna Biscevic) 등이다.범위는 지오텍스타일, 지오멤브레인, 토목합성재료 점토 차수재 및 기타 토목합성 관련 제품을 포함한 모든 토목합성 제품의 표준화다.현재 ISO/TC 221 사무국의 직접적인 책임 하에 발행된 표준은 47개며 ISO/TC 221 사무국의 직접적인 책임 하에 개발 중인 표준은 12개다. 참여하고 있는 회원은 30개국, 참관 회원은 16개국이다.□ ISO/TC 221 사무국의 직접적인 책임 하에 발행된 표준 47개 중 15개 목록▷ISO 9862:2023 Geosynthetics — Sampling and preparation of test specimens▷ISO 9863-1:2016 Geosynthetics — Determination of thickness at specified pressures — Part 1: Single layers▷ISO 9863-1:2016/Amd 1:2019 Geosynthetics — Determination of thickness at specified pressures — Part 1: Single layers — Amendment 1▷ISO 9864:2005 Geosynthetics — Test method for the determination of mass per unit area of geotextiles and geotextile-related products▷ISO 10318-1:2015 Geosynthetics — Part 1: Terms and definitions▷ISO 10318-1:2015/Amd 1:2018 Geosynthetics — Part 1: Terms and definitions — Amendment 1▷ISO 10318-2:2015 Geosynthetics — Part 2: Symbols and pictograms▷ISO 10318-2:2015/Amd 1:2018 Geosynthetics — Part 2: Symbols and pictograms — Amendment 1▷ISO 10319:2015 Geosynthetics — Wide-width tensile test▷ISO 10320:2019 Geosynthetics — Identification on site▷ISO 10321:2008 Geosynthetics — Tensile test for joints/seams by wide-width strip method▷ISO 10722:2019 Geosynthetics — Index test procedure for the evaluation of mechanical damage under repeated loading — Damage caused by granular material (laboratory test method)▷ISO 10769:2011 Clay geosynthetic barriers — Determination of water absorption of bentonite▷ISO 10772:2012 Geotextiles - Test method for the determination of the filtration behaviour of geotextiles under turbulent water flow conditions▷ISO 10773:2011 Clay geosynthetic barriers — Determination of permeability to gases□ ISO/TC 221 사무국의 직접적인 책임 하에 개발 중인 표준 12개 목록▷ISO/AWI 10318-1 Geosynthetics — Part 1: Terms and definitions▷ISO/AWI 10318-2 Geosynthetics — Part 2: Symbols and pictograms▷ISO/DIS 10319 Geosynthetics — Wide-width tensile test▷ISO/DIS 12236 Geosynthetics — Static puncture test (CBR test)▷ISO/DIS 12957-2 Geosynthetics — Determination of friction characteristics — Part 2: Inclined plane test▷ISO/FDIS 13426-2 Geotextiles and geotextile-related products — Strength of internal structural junctions — Part 2: Geocomposites▷ISO/DIS 13428 Geosynthetics — Determination of the protection efficiency of a geosynthetic against impact damage▷ISO/FDIS 13431 Geotextiles and geotextile-related products — Determination of tensile creep and creep rupture behaviour▷ISO/DIS 13433 Geosynthetics — Determination of dynamic perforation (cone drop test)▷ISO/CD TR 18228-5 Design using geosynthetics — Part 5: Stabilization▷ISO/DTR 18228-8 Design using geosynthetics — Part 8: Surface erosion control▷ISO/TR 18228-10 Design using geosynthetics — Part 10: Asphalt pavements
-
3GPP, 2025년 3월 한국 개최 회의부터 6G 연구 시작한국정보통신기술협회(회장 손승현, 이하 TTA)에 따르면 3월 18일~19일까지 5G 성능을개선하고 새로운 유스케이스와 확장된 융합 서비스를 지원하는5G-Advanced 표준(Release 18)이 3GPP 기술총회에서 승인됐다. 3GPP 기술총회는 네덜란드 마스트리히트에서 개최됐으며 삼성전자, LG전자, 애플, 퀄컴, 에릭슨, 노키아, 화웨이 등 글로벌 제조사와 SKT, KT, LGU+, ETRI, 버라이존, AT&T, 오렌지 등 국내외 이동통신사업자 및 연구소에서 약 600여명의 전문가들 참석했다. 2024년 6월 기술총회에서 비지상망 개선/실감 오디오 코덱 등 추가 보완이필요한 기능은 구현 규격과 함께 상세 기능규격에 대한 승인 등 최종 완료될 예정이다. 3GPP는 신규 기능이나 개선 사항 도입을 위해 Release 단위의 기술규격 세트 표준을 개발하고 있다. Release 15부터 17까지가 5G 규격이며 이번 Release 18부터가 5G-Advanced 규격으로 구분된다. 5G 표준이 5G 서비스 상용화와 융합 서비스 생태계 조성에 초점이 맞추어졌다. Release 18은 5G 시스템의 성능과 기능을 향상시키는 동시에 새로운 유스케이스로 확장·지원하고 6G로의 진화를 위한 신규 기술 연구도 포함된다. 구체적으로 다중 안테나 기술(MIMO) 개선으로 상하향 링크 용량과 성능이 추가 향상되었다. 또한 상향링크 개선 및 스마트중계기 도입을 통한 서비스 커버리지 향상, 레이어1/2 기반 핸드오버 지원으로 단말 이동성 관리 최적화 등의 성능 개선이 이루어졌다. XR(eXtended Reality)과 같은 새로운 유스케이스를 지원하고 특화망(NPN), 비지상 네트워크(NTN), 사이드링크, 위치 서비스, 엣지컴퓨팅, 단말 정책 및 네트워크 슬라이싱 개선 등을 통해 초신뢰 및 저지연에 대한 요구사항을 강화했다. 네트워크 에너지 효율 향상을 위해 Release 18에서 공간 및 전력 측면에서 네트워크 에너지 절감 기술을 도입하고 단말 전력 소비 감소를위해 저전력 웨이크업 신호 활용에 대한 연구도 수행했다. 동적이고 유연한 주파수 활용을 위해 서브밴드 전이중화(Sub-BandFull Duplex) 방식 연구, 무선 인터페이스에서 AI(Artificial Intelligence)/ML(Machine Learning) 도입을 위해 측위 및 빔 관리 등에 대한 유스케이스 연구 등 6G로의 진화 기술에 대한 준비도 시작됐다. 이번회의에서 3GPP 6G 표준화 일정이 보다 구체화되었으며 사업자와 제조사들의 6G 추진 전략 수립을 위한 청사진이 제시됐다. 3GPP는 ITU의 IMT-2030 요구사항 연구에 맞춰, ’25년 3월 3GPP기술 워크숍 이후부터 총회 차원의 6G 연구를 진행할 예정이다. 본격적인 6G 연구(Release 20)는 21개월 간 수행하기로 했으며 6G 기술(Release 21) 표준화는 구현 규격 완료일정을 ‘29.3월 이후로 추진하기로 합의했다. 이외 상세 일정은 2026년 6월 이전까지 확정할 예정이다. TTA 손승현 회장은 '이번 Release 18 표준화 완료로 5G 대비 개선된 성능을 보장하고 새로운 유스케이스를 지원하는 5G-Advanced 시대가 열렸다.'고 평가했다. '5G-Advanced는 5G 네트워크 진화의 중요한 진전이자, 6G의 가교로서도 중요한 표준으로 올해부터 본격 시작되는 Release 19 표준화에도 국내 산업계의 적극 대응이 필요하다.'고 덧붙였다. TTA는 과기정통부, 정보통신기획평가원(IITP)과 민·관 협력을 통해 2025년3월 3GPP 기술총회와 연계한ㅌ 3GPP 6G 기술 워크숍도 우리나라에서 유치해 3GPP 국제 표준화를 선도하고 있다.
-
[특집-기술위원회] TC 215 - 의료 정보학(Health informatics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 △1996년 TC 213, TC 214 등이 있다.ISO/TC 215 의료 정보학(Health informatics)과 관련된 기술위원회는 1998년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 레이첼 호손(Ms Rachel Hawthorne)가 책임지고 있다. 현재 의장은 토드 쿠퍼(Mr Todd Cooper)이며 임기는 2026년 말까지다. ISO 기술 프로그램 관리자는 마호 다카하시(Mme Maho Takahashi), ISO 편집 관리자는 발레리아 아가넨노네(Ms Valeria Agamennone) 등이다.범위는 의료 관련 데이터, 의료 시스템의 모든 측면을 지원하고 활성화하는 지식의 수집, 교환 및 사용을 촉진하기 위한 의료 정보학 분야의 표준화다.현재 ISO/TC 215 사무국과 관련해 발행된 표준은 237개며 ISO/TC 215 사무국의 직접적인 책임 하에 발행된 표준은 225개다.ISO/TC 215과 관련해 개발 중인 표준은 64개며 이중 ISO/TC 215 사무국의 직접적인 책임 하에 개발 중인 표준은 62개다. 참여하고 있는 회원은 35개국, 참관 회원은 32개국이다.□ ISO/TC 215 사무국의 직접적인 책임 하에 발행된 표준 225개 중 15개 목록▷ISO 1828:2012 Health informatics — Categorial structure for terminological systems of surgical procedures▷ISO/TR 4421:2023 Health informatics — Introduction to Ayurveda informatics▷ISO/TS 5044:2023 Health informatics — Information model for quality control of traditional Chinese medicinal products▷ISO/TS 5118:2022 Health informatics — Categorial structure of representation for evaluation of clinical practice guidelines of traditional Chinese medicine▷ISO/TS 5346:2022 Health informatics — Categorial structure for representation of traditional Chinese medicine clinical decision support system▷ISO 5477:2023 Health informatics — Interoperability of public health emergency preparedness and response information systems▷ISO/TS 5499:2024 Health informatics — Clinical particulars — Core principles for the harmonization of therapeutic indications terms and identifiers▷ISO/TS 5568:2022 Health informatics — Traditional Chinese medicine — Labelling metadata of human biological sample information▷ISO/TS 5569:2023 Health informatics — Conceptual data model for Chinese medicinal herbs▷ISO/TR 9143:2023 Health informatics — Sex and gender in electronic health records▷ISO 10159:2011 Health informatics — Messages and communication — Web access reference manifest▷ISO 10781:2023 Health informatics — HL7 Electronic Health Record-System Functional Model, Release 2.1 (EHR FM)▷ISO/IEEE 11073-00103:2015 Health informatics — Personal health device communication — Part 00103: Overview▷ISO/IEEE 11073-10101:2020 Health informatics — Device interoperability — Part 10101: Point-of-care medical device communication — Nomenclature▷ISO/IEEE 11073-10102:2014 Health informatics — Point-of-care medical device communication — Part 10102: Nomenclature — Annotated ECG□ ISO/TC 215 사무국의 직접적인 책임 하에 개발 중인 표준 62개 중 15개 목록▷ISO/AWI TR 4419 Health informatics — Reducing clinicians burden▷ISO/DTS 5384 Health informatics - Categorial Structure and Data Elements for the Identification and Exchange of Immunization Data▷ISO/CD TS 5615 Health informatics — Accelerating Safe, Effective and Secure Remote Connected Care and Mobile Health Through Standards-Based Interoperability Solutions Addressing Gaps Revealed by Pandemics▷ISO/DTS 5777 Health informatics — The architecture of internet healthcare service network▷ISO/DTS 5788 Health informatics — Internet healthcare service pattern▷ISO/CD TS 6201.2 Health Informatics — Personalized Digital Health -Framework▷ISO/CD TS 6204 Health Informatics — Categorial structures for representation of Ayurvedic medicinal water — Decocting process in Ayurveda▷ISO/AWI TS 6226 Health informatics — Reference architecture for syndromic surveillance systems for infectious diseases▷ISO/DTR 6231 Health informatics — Standardizing graphical content▷ISO/CD TS 6268-1 Health informatics — Cybersecurity framework for telehealth environments — Part 1: Overview and Concepts▷ISO/AWI TS 6268-2 Health informatics — Cybersecurity framework for telehealth environments — Part 2: Cybersecurity reference models of telehealth▷ISO/CD TS 7122 Health Informatics — Guidelines for exchanging data generated by POCT (Point of Care Testing) devices between screening center and clinical laboratory▷ISO/AWI TS 9166 Health Informatics — Guidelines for self-assessment questionnaire systems▷ISO/DTS 9320 Health informatics — Standardized data set for transfer of hemodialysis patients▷ISO/DTS 9321 Health informatics — General requirements of multi-centre medical data collaborative analysis□ ISO/TC 215 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 215/SC 1 Genomics Informatics ; 발행된 표준 12개, 개발 중인 표준 2개
-
[특집-기술위원회] TC 214 - 승강기 작업 플랫폼(Elevating work platforms)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 등이 있다.ISO/TC 214 승강기 작업 플랫폼(Elevating work platforms)과 관련된 기술위원회는 TC 213과 마찬가지로 1996년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 샐리 사이츠(Ms Sally Seitz)가 책임지고 있다. 현재 의장은 스티븐 A. 베스트(Mr Stephen A. Best)이며 임기는 2029년 말까지다. ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 앤 기엣(Ms Anne Guiet) 등이다.범위는 용어, 등급, 일반 원칙(기술적 성능 요구 사항 및 위험 평가), 안전 요구사항, 테스트 방법, 유지관리, 승강에 사용되는 작업 플랫폼을 올리기 위한 조작 등의 표준화다. 또한 작업을 수행할 작업 위치에 직원(및 관련 작업 도구, 자재 등)을 배치에 대한 표준화도 포함된다.현재 ISO/TC 214 사무국의 직접적인 책임 하에 발행된 표준은 9개며 ISO/TC 214 사무국의 직접적인 책임 하에 개발 중인 표준은 3개다. 참여하고 있는 회원은 19개국, 참관 회원은 19개국이다.□ ISO/TC 214 사무국의 직접적인 책임 하에 발행된 표준 9개 목록▷ISO 16368:2010 Mobile elevating work platforms — Design, calculations, safety requirements and test methods▷ISO 16369:2007 Elevating work platforms — Mast-climbing work platforms▷ISO 16653-1:2008 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 1: MEWPs with retractable guardrail systems▷ISO 16653-2:2021 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 2: MEWPs with non-conductive (insulating) components▷ISO 16653-3:2011 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 3: MEWPs for orchard operations▷ISO 18878:2013 Mobile elevating work platforms — Operator (driver) training▷ISO 18893:2014 Mobile elevating work platforms — Safety principles, inspection, maintenance and operation▷ISO 20381:2009 Mobile elevating work platforms — Symbols for operator controls and other displays▷ISO 21455:2020 Mobile elevating work platforms — Operator's controls — Actuation, displacement, location and method of operation□ ISO/TC 214 사무국의 직접적인 책임 하에 개발 중인 표준 3개 목록▷ISO/FDIS 16368 Mobile elevating work platforms — Design, calculations, safety requirements and test methods▷ISO/DIS 18878 Mobile elevating work platforms — Operator (driver) training▷ISO/DIS 18893 Mobile elevating work platforms — Safety principles, inspection, maintenance and operation
-
[특집-기술위원회] TC 213 - 치수와 기하학적 제품의 사양 및 검증(Dimensional and geometrical product specifications and verification)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 등이 있다.ISO/TC 213 치수와 기하학적 제품의 사양 및 검증(Dimensional and geometrical product specifications and verification)과 관련된 기술위원회는 1996년 결성됐다. 사무국은 영국 표준협회(British Standards Institution, BSI)에서 맡고 있다.위원회는사라 켈리(Miss Sarah Kelly)가 책임지고 있다. 현재 의장은 이안 맥클라우드(Mr Iain Macleod)이며 임기는 2025년말까지다. ISO 기술 프로그램 관리자는 이사벨 베가(Ms Isabelle Vega), ISO 편집 관리자는 니콜라 페루(Ms Nicola Perou) 등이다.범위는 기하학적 제품 사양(GPS) 분야의 표준화다. 즉 치수 및 기하학적 공차, 표면 특성 및 관련 검증 원리, 치수 및 기하학적 측정의 불확실성을 포함한 측정 장비 및 교정 요구 사항을 다루는 거시 및 미세 형상 사양이다.표준화에는 기본 레이아웃과 도면 표시(기호)에 대한 설명이 포함된다. 단, 도면 표시(기호)의 특정 비율 및 치수 정의, 실행은 제외된다.현재 ISO/TC 213 사무국의 직접적인 책임 하에 발행된 표준은 147개며 ISO/TC 213 사무국의 직접적인 책임 하에 개발 중인 표준은 22개다. 참여하고 있는 회원은 26개국, 참관 회원은 25개국이다.□ ISO/TC 213 사무국의 직접적인 책임 하에 발행된 표준 147개 중 15개 목록▷ISO 1:2022 Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties▷ISO 286-1:2010 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits▷ISO 286-1:2010/Cor 1:2013 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits — Technical Corrigendum 1▷ISO 286-2:2010 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts▷ISO 286-2:2010/Cor 1:2013 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts — Technical Corrigendum 1▷ISO 463:2006 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges▷ISO 463:2006/Cor 1:2007 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 1▷ISO 463:2006/Cor 2:2009 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 2▷ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out▷ISO 1119:2011 Geometrical product specifications (GPS) — Series of conical tapers and taper angles▷ISO 1660:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing▷ISO 1938-1:2015 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size▷ISO 1938-2:2017 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Reference disk gauges▷ISO 2538-1:2014 Geometrical product specifications (GPS) — Wedges — Part 1: Series of angles and slopes▷ISO 2538-2:2014 Geometrical product specifications (GPS) — Wedges — Part 2: Dimensioning and tolerancing□ ISO/TC 213 사무국의 직접적인 책임 하에 개발 중인 표준 22개 중 15개 목록▷ISO/CD 1938-1 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size▷ISO/AWI 2768 General tolerances▷ISO/DIS 5059-1 Geometrical product specifications (GPS) — Dimensional measuring equipment: inside micrometers — Part 1: Two-point inside micrometers — Design and metrological characteristics▷ISO/FDIS 5459 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems▷ISO/DIS 5463 Geometrical product specifications (GPS) — Form measuring equipment; Rotary axis form measuring instruments — Design and metrological characteristics▷ISO/CD 10360-102 Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 102: The language of symbols G3▷ISO/AWI 12179 Geometrical product specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments▷ISO/DIS 14405-1 Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes▷ISO/CD TS 15530-2 Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 2: Part 2: Evaluating task-specific measurement uncertainty by multiple measurement strategies using a single uncalibrated workpiece▷ISO/DIS 16610-21 Geometrical product specifications (GPS) — Filtration — Part 21: Linear profile filters: Gaussian filters▷ISO/CD 16610-22 Geometrical product specifications (GPS) — Filtration — Part 22: Linear profile filters: Spline filters▷ISO/DIS 16610-31 Geometrical product specifications (GPS) — Filtration — Part 31: Robust profile filters: Gaussian regression filters▷ISO/DIS 16610-45 Geometrical product specifications (GPS) — Filtration — Part 45: Morphological profile filters: Segmentation▷ISO 18183-1 Geometrical product specifications (GPS) — Partition — Part 1: Vocabulary and basic concepts▷ISO/CD TR 23850 Geometrical product specifications (GPS) — Association — Mathematical concepts
-
[특집-기술위원회] TC 212 - 의료 실험실 및 체외 진단 시스템(Medical laboratories and in vitro diagnostic systems)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 등이 있다.ISO/TC 212 의료 실험실 및 체외 진단 시스템(Medical laboratories and in vitro diagnostic systems)과 관련된 기술위원회는 TC 210, TC 211과 마찬가지로 1994년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는데이비드 스테리(Mr David Sterry)가 책임지고 있다. 현재 의장은 헤수스 루에다 로드리게스(Mr Jesus Rueda Rodriguez)이며 임기는 2027년말까지다. ISO 기술 프로그램 관리자는 이사벨 베가(Ms Isabelle Vega), ISO 편집 관리자는 발레리아 아가넨노네(Ms Valeria Agamennone) 등이다.범위는 의료 실험실 및 체외 진단 시스템 분야의 표준화 및 지침이다. 여기에는 품질 관리, 분석 전후 절차, 분석 성능, 실험실 안전, 참조 시스템 및 품질 보증 등이 포함된다.단, ISO/TC 176에서 다루는 일반 품질 관리 표준, ISO/TC 210에서 다루는 의료기기 품질 관리 표준, ISO/TC 334 참조 자료 위원회(REMCO)에서 다루는 참조 자료 지침, ISO 적합성 평가 위원회(CASCO)에서 다루는 적합성 평가 지침 등은 제외된다현재 ISO/TC 212 사무국의 직접적인 책임 하에 발행된 표준은 47개며 ISO/TC 212 사무국의 직접적인 책임 하에 개발 중인 표준은 23개다. 참여하고 있는 회원은 41개국, 참관 회원은 33개국이다.□ ISO/TC 212 사무국의 직접적인 책임 하에 발행된 표준 47개 중 15개 목록▷ISO 4307:2021 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for saliva — Isolated human DNA▷ISO/TS 5798:2022 In vitro diagnostic test systems — Requirements and recommendations for detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) by nucleic acid amplification methods▷ISO 15189:2022 Medical laboratories — Requirements for quality and competence▷ISO 15190:2020 Medical laboratories — Requirements for safety▷ISO 15193:2009 In vitro diagnostic medical devices — Measurement of quantities in samples of biological origin — Requirements for content and presentation of reference measurement procedures▷ISO 15194:2009 In vitro diagnostic medical devices — Measurement of quantities in samples of biological origin — Requirements for certified reference materials and the content of supporting documentation▷ISO 15195:2018 Laboratory medicine — Requirements for the competence of calibration laboratories using reference measurement procedures▷ISO 15197:2013 In vitro diagnostic test systems — Requirements for blood-glucose monitoring systems for self-testing in managing diabetes mellitus▷ISO 15198:2004 Clinical laboratory medicine — In vitro diagnostic medical devices — Validation of user quality control procedures by the manufacturer▷ISO 16256:2021 Clinical laboratory testing and in vitro diagnostic test systems — Broth micro-dilution reference method for testing the in vitro activity of antimicrobial agents against yeast fungi involved in infectious diseases▷ISO/TS 16782:2016 Clinical laboratory testing — Criteria for acceptable lots of dehydrated Mueller-Hinton agar and broth for antimicrobial susceptibility testing▷ISO 17511:2020 In vitro diagnostic medical devices — Requirements for establishing metrological traceability of values assigned to calibrators, trueness control materials and human samples▷ISO/TS 17518:2015 Medical laboratories — Reagents for staining biological material — Guidance for users▷ISO 17593:2022 Clinical laboratory testing and in vitro medical devices — Requirements for in vitro monitoring systems for self-testing of oral anticoagulant therapy▷ISO 17822:2020 In vitro diagnostic test systems — Nucleic acid amplification-based examination procedures for detection and identification of microbial pathogens — Laboratory quality practice guide□ ISO/TC 212 사무국의 직접적인 책임 하에 개발 중인 표준 23개 중 15개 목록▷ISO/DTS 5441 Competence requirements for biorisk management advisors▷ISO/DIS 5649 Medical laboratories — Concepts and specifications for the design, development, implementation, and use of laboratory-developed tests▷ISO/AWI TS 7446 ISO 35001 — Biorisk management for laboratories and other related organisations — Implementation guidance▷ISO/CD TS 7552-1 Specifications for pre-examination processes for circulating tumor cells (CTCs) in venous whole blood — Part 1: Isolated RNA▷ISO/CD TS 7552-2 Specifications for pre-examination processes for circulating tumor cells (CTCs) in venous whole blood — Part 2: Isolated DNA▷ISO/CD TS 7552-3 Specifications for pre-examination processes for circulating tumor cells (CTCs) in venous whole blood — Part 3: Preparations for analytical CTC staining▷ISO/AWI TS 8219 Sequencing and clinical application to infectious diseases▷ISO/DIS 15193 In vitro diagnostic medical devices — Requirements for reference measurement procedures▷ISO/DIS 15194 In vitro diagnostic medical devices — Requirements for certified reference materials and the content of supporting documentation▷ISO/CD TS 16766.2 Manufacturers’considerations for in vitro diagnostic medical devices in a public health crisis▷ISO/AWI TS 18701 Molecular in vitro diagnostic examinations — Specificationsfor pre-examination processes for human specimens — Isolated microbiome DNA▷ISO/AWI TS 18702 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for exosomes and other extracellular vesicles in venous whole blood — DNA, RNA and proteins▷ISO/AWI 18703 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for venous whole blood — Isolated circulating cell free RNA from plasma▷ISO/CD 18704 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for urine and other body fluids — Isolated cell free DNA▷ISO/DIS 21474-3 In vitro diagnostic medical devices — Multiplex molecular testing for nucleic acids — Part 3: Interpretation and reports