검색결과
-
[특집-기술위원회] TC 178 - 리프트·에스컬레이터·무빙워크(Lifts·escalators·moving walks)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 등이 있다.ISO/TC 178 리프트, 에스컬레이터, 무빙워크(Lifts, escalators and moving walks)와 관련된 기술위원회는 TC 176과 마찬가지로 1979년 결성됐다. 사무국은 프랑스 표준화기구(Association Française de Normalization, AFNOR)에서 맡고 있다.위원회는 에바 콘티발(Mme Eva Contival)가 책임지고 있으며 현재 의장은 게로 그슈벤트너(Dr Gero Gschwendtner)다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 마사 카산토산(Mrs Martha Casantosan) 등으로 조사됐다.범위는 리프트, 서비스 리프트, 승객용 컨베이어, 유사 장치 등의 안전을 포함해 모든 사양의 표준화다. 단 지속적인 기계적 취급 장비 및 광산 리프트는 제외한다.현재 ISO/TC 178 사무국의 직접적인 책임 하에 발행된 표준은 43개며 ISO/TC 178 사무국의 직접적인 책임 하에 개발 중인 표준은 15개다. 참여하고 있는 회원은 31개국, 참관 회원은 27개국이다.□ ISO/TC 178 사무국의 직접적인 책임 하에 발행된 표준 43개 중 15개 목록▷ISO 4190-2:2001 Lift (US: Elevator) installation — Part 2: Class IV lifts▷ISO 4190-3:1982 Passenger lift installations — Part 3: Service lifts class V▷ISO 4190-5:2006 Lift (Elevator) installation — Part 5: Control devices, signals and additional fittings▷ISO 8100-1:2019 Lifts for the transport of persons and goods — Part 1: Safety rules for the construction and installation of passenger and goods passenger lifts▷ISO 8100-2:2019 Lifts for the transport of persons and goods — Part 2: Design rules, calculations, examinations and tests of lift components▷ISO/TS 8100-3:2019 Lifts for the transport of persons and goods — Part 3: Requirements from other Standards (ASME A17.1/CSA B44 and JIS A 4307-1/JIS A 4307-2) not included in ISO 8100-1 or ISO 8100-2▷ISO 8100-20:2018 Lifts for the transport of persons and goods — Part 20: Global essential safety requirements (GESRs)▷ISO/TS 8100-21:2018 Lifts for the transport of persons and goods — Part 21: Global safety parameters (GSPs) meeting the global essential safety requirements (GESRs)▷ISO/TR 8100-24:2016 Safety requirements for lifts (elevators) — Part 24: Convergence of lift requirements▷ISO 8100-30:2019 Lifts for the transport of persons and goods — Part 30: Class I, II, III and VI lifts installation▷ISO 8100-32:2020 Lifts for the transportation of persons and goods — Part 32: Planning and selection of passenger lifts to be installed in office, hotel and residential buildings▷ISO 8100-33:2022 Lifts for the transport of persons and goods — Part 33: T-type guide rails for lift cars and counterweights▷ISO 8100-34:2021 Lifts for the transport of persons and goods — Part 34: Measurement of lift ride quality▷ISO 8102-1:2020 Electrical requirements for lifts, escalators and moving walks — Part 1: Electromagnetic compatibility with regard to emission▷ISO 8102-2:2021 Electrical requirements for lifts, escalators and moving walks — Part 2: Electromagnetic compatibility with regard to immunity□ ISO/TC 178 사무국의 직접적인 책임 하에 개발 중인 표준 15개 목록▷ISO/DIS 8100-1 Lifts for the transport of persons and goods — Part 1: Safety rules for the construction and installation of passenger and goods passenger lifts▷ISO/DIS 8100-2 Lifts for the transport of persons and goods — Part 2: Design rules, calculations, examinations and tests of lift components▷ISO/AWI 8100-7 Lifts for the transport of persons and goods — Part 7: Accessibility to lifts for persons including persons with disability▷ISO/WD TS 8100-10 Lifts for the transport of persons and goods — Part 10: Building Information Modelling▷ISO/CD TS 8100-22 Lifts for the transport of persons and goods — Part 22: Prerequisites for certification of conformity of lift systems, lift components and lift functions within conformity assessment procedures▷ISO/CD TS 8100-23 Lifts for the transport of persons and goods — Part 23: Certification and accreditation requirements within conformity assessment procedures▷ISO/CD TR 8101-10 Fire safety on lifts — Part 10: Comparison of worldwide safety standards on lifts for firefighters▷ISO/AWI 8102-1 Electrical requirements for lifts, escalators and moving walks — Part 1: Electromagnetic compatibility with regard to emissions▷ISO/AWI 8102-2 Electrical requirements for lifts, escalators and moving walks — Part 2: Electromagnetic compatibility with regard to immunity▷ISO/WD TS 8102-21 Electrical requirements for lifts, escalators and moving walks — Part 21: Part 21: On-site and off-site software updates▷ISO/DIS 8103-1 Escalators and moving walks — Part 1: Safety requirements▷ISO/WD TS 8103-3 Escalators and moving walks — Part 3: Part 3: Requirements from other Standards (ASME A17.1/CSA B44 and JIS codes) not included in ISO▷ISO/AWI 8103-9 Escalators and moving walks — Part 9: Measurement of ride quality▷ISO/DTR 25741-1 Lifts and escalators subject to seismic conditions — Compilation report — Part 1: Rule by rule comparison▷ISO/DTR 25741-2 Lifts and escalators subject to seismic conditions — Compilation report — Part 2: Abbreviated comparison and comments
-
[특집-기술위원회] TC 176 - 품질관리 및 품질보증(Quality management and quality assurance)… 특정 부문 품질관리 표준화뿐만 아니라 일반 품질관리시스템 및 지원 기술과 같은 품질관리 분야의 표준화스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 등이 있다.ISO/TC 176 품질관리 및 품질보증(Quality management and quality assurance)과 관련된 기술위원회는 1979년 결성됐다. 사무국은 캐나다 표준위원회(Standards Council of Canada, SCC)에서 맡고 있다.위원회는마크 슈슬러(Mr Mark Schuessler)가 책임지고 있으며 현재 의장은 제프리 헌트(Mr Jeffrey Hunt)다. ISO 기술 프로그램 관리자는 호세 알코르타(Mr José Alcorta), ISO 편집 관리자는 니콜라 페루(Ms Nicola Perou) 등으로 조사됐다.범위는 ISO 기술 관리위원회의 요청에 따라 특정 부문 품질관리 표준화뿐만 아니라 일반 품질관리시스템 및 지원 기술과 같은 품질관리 분야의 표준화다.참고로 ISO/TC 176은 일반 품질시스템 표준의 무결성과 품질관리시스템 결과물에 대한 ISO/IEC 부문 정책의 효과적인 구현을 보장하기 위해 모든 ISO 및 IEC 기술 위원회에 자문 기능을 맡겼다.현재 ISO/TC 176 사무국과 관련해 발행된 표준은 23개며 ISO/TC 176 사무국의 직접적인 책임 하에 발행된 표준은 2개다.ISO/TC 176 사무국과 관련해 개발 중인 표준은 6개며 ISO/TC 176 사무국의 직접적인 책임 하에 개발 중인 표준은 1개다. 참여하고 있는 회원은 93개국, 참관 회원은 33개국이다.□ ISO/TC 176 사무국의 직접적인 책임 하에 발행된 표준 2개 목록▷ISO 18091:2019 Quality management systems — Guidelines for the application of ISO 9001 in local government▷ISO/TS 54001:2019 Quality management systems — Particular requirements for the application of ISO 9001:2015 for electoral organizations at all levels of government□ ISO/TC 176 사무국의 직접적인 책임 하에 개발 중인 표준 1개 목록▷ISO/CD 54002 Quality management systems - Guidelines for the application of ISO 9001 in police organizations□ ISO/TC 176 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 176/SC 1 Uniaxial testing ; 발행된 표준 1개, 개발 중인 표준 1개▷ISO/TC 176/SC 2 Quality systems ; 발행된 표준 6개, 개발 중인 표준 2개▷ISO/TC 176/SC 3 Supporting technologies ; 발행된 표준 14개, 개발 중인 표준 2개
-
[특집-기술위원회] TC 171 - 문서 관리 어플리케이션(Document management applications)… 캡처·색인화·저장·검색·배포 및 통신·프리젠테이션·마이그레이션스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.△1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 등도 포함된다.ISO/TC 171 문서 관리 어플리케이션(Document management applications)과 관련된 기술위원회는 1978년 결성됐다. 사무국은 영국 표준 기구(British Standards Institution, BSI))에서 맡고 있다.위원회는 진 스트라이드(Mrs Jean M Stride)가 책임지고 있으며 현재 의장은 앨런 쉽먼(Mr Alan Shipman)이며 임기는 2026년까지다.ISO 기술 프로그램 관리자는 페트리샤 쿡(Mme Patricia Cook), ISO 편집 관리자는 이사벨 베로니카 넬슨(Ms Isabel Veronica Nelson) 등으로 조사됐다.범위는 문서 관리 애플리케이션 분야의 캡처, 색인화, 저장, 검색, 배포 및 통신, 프리젠테이션, 마이그레이션, 교환, 보존, 무결성 유지 및 폐기와 관련된 기술 및 프로세스의 표준화다. 문서는 마이크로그래픽 또는 전자형식으로 관리될 수 있다.또한 품질 관리 및 무결성 유지 관리, 문서의 입력/출력 품질(현미경 또는 전자), 지원 메타데이터를 포함해 문서(현미경 또는 전자)의 저장, 사용 및 보존을 위한 구현, 검사 및 품질 관리 절차, 기업 및 인터넷의 작업 흐름(프로세스 관리)과 관련된 애플리케이션, 시스템 간 정보 교환 중 품질 및 무결성 유지, 법적 허용성 및(또는) 무결성 및 보안을 지원하는 절차 및 프로세스, 관련 감사 추적 정보 등도 포함된다.단, TC 46의 범위 내에서 기록 관리 정책 및 절차, TC 184 범위 내에서 산업 자동화 시스템의 정보, 프로세스, 생산 정의 및 작업 흐름에 관한 모든 작업은 제외한다.사진에 적용되는 프로세스, 재료 및 장치의 성능 특성을 테스트, 평가, 분류 및 지정하는 작업을 다룹니다.원본 필름의 촬영, 치수 및 라벨링, ISO/TC 42 범위내 방법 사진에 적용되는 프로세스, 재료 및 장치의 성능 특성을 테스트, 평가, 분류 및 지정하는 작업을 다룹니다.영화 촬영, 원본 필름의 치수 및 라벨링, 사진에 적용할 수 있는 프로세스, 재료 및 장치의 성능 특성을 테스트, 평가, 분류 및 지정하는 ISO/TC 42 범위 내 방법 등도 제외된다.ISO/IEC JTC1의 범위 내에 있는 작업, 특히 ISO/IEC JTC 1/SC 23, SC 24, SC 27, SC 28, SC 29, SC 32 및 SC 34의 작업 역시 제외한다. 참고로 다른 TC와 잠재적 또는 실제 중복이 존재하는 경우 JWG가 적극적으로 추진된다.현재 ISO/TC 171 사무국과 관련해 발행된 표준은 108개 이며 이 중 ISO/TC 171 사무국의 직접적인 책임 하에 발행된 표준은 50개다. ISO/TC 171 사무국과 관련해 개발 중인 표준은 10개다. 참여하고 있는 회원은 16개국, 참관 회원은 31개국이다.□ ISO/TC 171 사무국의 직접적인 책임 하에 발행된 표준 50개 중 15개 목록▷ISO 446:2004 Micrographics — ISO character and ISO test chart No. 1 — Description and use▷ISO 3272-1:2003 Microfilming of technical drawings and other drawing office documents — Part 1: Operating procedures▷ISO 3272-1:2003/Cor 1:2009 Microfilming of technical drawings and other drawing office documents — Part 1: Operating procedures — Technical Corrigendum 1▷ISO 3272-2:1994 Microfilming of technical drawings and other drawing office documents — Part 2: Quality criteria and control of 35 mm silver gelatin microfilms▷ISO 3272-3:2001 Microfilming of technical drawings and other drawing office documents — Part 3: Aperture card for 35 mm microfilm▷ISO 3272-4:1994 Microfilming of technical drawings and other drawing office documents — Part 4: Microfilming of drawings of special and exceptional elongated sizes▷ISO 3272-6:2000 Microfilming of technical drawings and other drawing office documents — Part 6: Quality criteria and control of systems for enlargements from 35 mm microfilm▷ISO 3334:2006 Micrographics — ISO resolution test chart No. 2 — Description and use▷ISO 4087:2005 Micrographics — Microfilming of newspapers for archival purposes on 35 mm microfilm▷ISO 6148:2001 Photography — Micrographic films, spools and cores — Dimensions▷ISO 6196-1:1993 Micrographics — Vocabulary — Part 1: General terms▷ISO 6196-2:1993 Micrographics — Vocabulary — Part 2: Image positions and methods of recording▷ISO 6196-3:1997 Micrographics — Vocabulary — Part 3: Film processing▷ISO 6196-4:1998 Micrographics — Vocabulary — Part 4: Materials and packaging▷ISO 6196-5:1987 Micrographics — Vocabulary — Part 5: Quality of images, legibility, inspection□ ISO/TC 171 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 171/SC 1 Quality, preservation and integrity of information ; 발행된 표준 21개, 개발 중인 표준 3개▷ISO/TC 171/SC 2 Document file formats, EDMS systems and authenticity of information ; 발행된 표준 37개, 개발 중인 표준 7개
-
[특집-기술위원회] TC 163 - 건축환경의 열 성능 및 에너지 사용(Thermal performance and energy use in the built environment)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.△1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 등도 포함된다.ISO/TC 163 건축환경의 열 성능 및 에너지 사용(Thermal performance and energy use in the built environment)과 관련된 기술위원회는 TC 162와 마찬가지로 1975년 결성됐다. 사무국은 스웨덴 표준협회(Swedish Institute for Standards, SIS)에서 맡고 있다.위원회는 벵트 리드슈테트(Mr Bengt Rydstedt)가 책임지고 있으며 현재 의장은 예스퍼 아르프비드손(Mr Jesper Arfvidsson)다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje) 등으로 조사됐다. 범위는 다음과 같은 건축 및 토목 공학 작업 분야의 표준화다. - 신축 및 기존 건물 전체를 포함한 재료, 제품, 부품, 요소 및 시스템의 열 및 습열 성능과 기술 건물 시스템과의 상호 작용 - 건물에 설치된 장비의 단열을 포함해 건축 및 산업용 단열재, 제품 및 시스템 - 열 및 습기 전달, 온도 및 습기 조건에 대한 테스트 및 계산 방법 - 산업 건축 환경을 포함한 건물의 에너지 사용에 대한 테스트 및 계산 방법 - 건물의 냉난방 부하에 대한 테스트 및 계산 방법 - 일광, 환기 및 공기 침투에 대한 테스트 및 계산 방법 - 건물 및 건물 구성요소의 열, 습열 및 에너지 성능에 대한 현장 테스트 방법, 기후 데이터를 포함한 계산을 위한 입력 데이터 - 관련 테스트 방법 및 적합성 기준이 포함된 단열재, 제품 및 시스템 사양 - 용어 - ISO 내 열 및 습열 성능에 대한 작업의 일반적인 검토 및 조정단, 건축 환경 설계(ISO/TC 205), 새로운 건물 및 개조 설계에 적용하기 위한 건물 환경 장비의 성능을 테스트하고 평가하는 방법(ISO/TC 205), 일광, 환기 및 공기 침투를 위한 설계 방법 및 기준(ISO/TC 205) 등은 제외한다.ISO/TC163/WG4 공동 작업 그룹 'TC 163 및 TC 205 에너지 성능'을 통해 ISO/TC 205와의 긴밀한 협력을 통해 건물 개조뿐 아니라 신규 건물과 기존 건물의 에너지 성능에 대한 전체적인 평가를 표준화하고 있다.ISO/TC163/WG4 공동 작업 그룹은 용어 및 정의, 건물 및 기술 시스템의 시스템 경계, 다음을 고려한 건물의 전반적인 에너지 성능 평가 등을 표준화한다. - 건축 요소의 에너지 성능 - 건물 관련 시스템(난방, 냉방, 가정용 온수, 환기, 조명, 시스템 제어, 운송 및 기타 에너지 관련 시스템) - 실내 및 실외 조건 - 지역 에너지 생산(현장 및 지역 수준) - (사용) 에너지원(재생 가능 포함) - 건물 시운전 - 전반적인 에너지 효율 평가 - 건축물의 에너지성능을 표현하는 수단 및 에너지성능 인증 등현재 ISO/TC 163 사무국과 관련해 발행된 표준은 152개며 이중 사무국의 직접적인 책임 하에 발행된 표준은 15개다. ISO/TC 16 사무국과 관련해 개발 중인 표준은 15개며 참여하고 있는 회원은 29개국, 참관 회원은 35개국이다.□ ISO/TC 163 사무국의 직접적인 책임 하에 발행된 표준 15개 목록▷ISO 7345:2018 Thermal performance of buildings and building components — Physical quantities and definitions▷ISO 9229:2020 Thermal insulation — Vocabulary▷ISO 9251:1987 Thermal insulation — Heat transfer conditions and properties of materials — Vocabulary▷ISO 9288:2022 Thermal insulation — Heat transfer by radiation — Vocabulary▷ISO 9346:2007 Hygrothermal performance of buildings and building materials — Physical quantities for mass transfer — Vocabulary▷ISO 12655:2013 Energy performance of buildings — Presentation of measured energy use of buildings▷ISO 17772-1:2017 Energy performance of buildings — Indoor environmental quality — Part 1: Indoor environmental input parameters for the design and assessment of energy performance of buildings▷ISO/TR 17772-2:2018 Energy performance of buildings — Overall energy performance assessment procedures — Part 2: Guideline for using indoor environmental input parameters for the design and assessment of energy performance of buildings▷ISO 18523-1:2016 Energy performance of buildings — Schedule and condition of building, zone and space usage for energy calculation — Part 1: Non-residential buildings▷ISO 18523-2:2018 Energy performance of buildings — Schedule and condition of building, zone and space usage for energy calculation — Part 2: Residential buildings▷ISO 52000-1:2017 Energy performance of buildings — Overarching EPB assessment — Part 1: General framework and procedures▷ISO/TR 52000-2:2017 Energy performance of buildings — Overarching EPB assessment — Part 2: Explanation and justification of ISO 52000-1▷ISO 52000-3:2023 Energy performance of buildings — Overarching EPB assessment — Part 3: General principles for determination and reporting of primary energy factors (PEF) and CO2 emission coefficients▷ISO 52003-1:2017 Energy performance of buildings — Indicators, requirements, ratings and certificates — Part 1: General aspects and application to the overall energy performance▷ISO/TR 52003-2:2017 Energy performance of buildings — Indicators, requirements, ratings and certificates — Part 2: Explanation and justification of ISO 52003-1□ ISO/TC 163 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 163/SC 1 Test and measurement methods ; 발행된 표준 76개, 개발 중인 표준 4개▷ISO/TC 163/SC 2 Calculation methods ; 발행된 표준 40개, 개발 중인 표준 3개▷ISO/TC 163/SC 3 Thermal insulation products, components and systems ; 발행된 표준 21개, 개발 중인 표준 8개
-
[특집-기술위원회] TC 160 - 건물 유리(Glass in building)… 영국 표준협회(BSI)가 사무국 운영스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.△1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 등도 포함된다.ISO/TC 160 건물 유리(Glass in building)와 관련된 기술위원회는 TC 156, TC 157, TC 158, TC 159와 마찬가지로 1974년 결성됐다. 사무국은 영국 표준협회(British Standards Institution, BSI)에서 맡고 있다.위원회는 톰 스택(Mr Tom Stack)이 책임지고 있으며 현재 의장은 노버트 브룩(Mr Dr Norbert Wruk)이다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 발레리아 아가넨노네(Ms Valeria Agamennone) 등으로 조사됐다.범위는 용어, 성능 요구사항, 계산 및 테스트 방법, 설계 및 시공 규칙, 치수 특성을 포함한 재료의 분류 및 사양을 포함한 건물 유리 분야의 표준화다.현재 ISO/TC 160 사무국의 직접적인 책임 하에 발행된 표준은 58개며 ISO/TC 160 사무국의 직접적인 책임 하에 개발 중인 표준은 10개다. 참여하고 있는 회원은 22개국, 참관 회원은 30개국이다.□ ISO/TC 160 사무국의 직접적인 책임 하에 발행된 표준 58개 중 15개 목록▷ISO 1288-1:2016 Glass in building — Determination of the bending strength of glass — Part 1: Fundamentals of testing glass▷ISO 1288-2:2016 Glass in building — Determination of the bending strength of glass — Part 2: Coaxial double-ring test on flat specimens with large test surface areas▷ISO 1288-3:2016 Glass in building — Determination of the bending strength of glass — Part 3: Test with specimen supported at two points (four point bending)▷ISO 1288-4:2016 Glass in building — Determination of the bending strength of glass — Part 4: Testing of channel shaped glass▷ISO 1288-5:2016 Glass in building — Determination of the bending strength of glass — Part 5: Coaxial double ring test on flat specimens with small test surface areas▷ISO 9050:2003 Glass in building — Determination of light transmittance, solar direct transmittance, total solar energy transmittance, ultraviolet transmittance and related glazing factors▷ISO 10291:1994 Glass in building — Determination of steady-state U values (thermal transmittance) of multiple glazing — Guarded hot plate method▷ISO 10292:1994 Glass in building — Calculation of steady-state U values (thermal transmittance) of multiple glazing▷ISO 10293:1997 Glass in building — Determination of steady-state U values (thermal transmittance) of multiple glazing — Heat flow meter method▷ISO 11479-1:2011 Glass in building — Coated glass — Part 1: Physical defects▷ISO 11479-2:2011 Glass in building — Coated glass — Part 2: Colour of façade▷ISO 11485-1:2011 Glass in building — Curved glass — Part 1: Terminology and definitions▷ISO 11485-2:2011 Glass in building — Curved glass — Part 2: Quality requirements▷ISO 11485-3:2014 Glass in building — Curved glass — Part 3: Requirements for curved tempered and curved laminated safety glass▷ISO 12540:2017 Glass in building — Tempered soda lime silicate safety glass □ ISO/TC 160 사무국의 직접적인 책임 하에 개발 중인 표준 10개 목록▷ISO/CD 16293-2 Glass in building — Basic soda lime silicate glass products — Part 2: Float glass▷ISO/CD 18178 Glass in building — Laminated solar photovoltaic glass for use in buildings▷ISO/CD 19916-4 Glass in building — Vacuum insulating glass — Part 4: Pendulum impact testing and classification of safety glass▷ISO/DIS 20492-1 Glass in buildings - Insulating glass — Part 1: Durability of edge seals by climate tests▷ISO/DIS 20492-2 Glass in buildings - Insulating glass — Part 2: Chemical fogging tests▷ISO/DIS 20492-3 Glass in buildings — Insulating glass — Part 3: Gas concentration and gas leakage▷ISO/DIS 20492-4 Glass in buildings — Insulating glass — Part 4: Methods of test for the physical attributes of edge seals▷ISO/CD 28278-1 Glass in building — Glass products for structural sealant glazing — Part 1: Supported and unsupported monolithic and multiple glazing▷ISO/CD 28278-2 Glass in building — Glass products for structural sealant glazing — Part 2: Assembly rules▷IEC/AWI 63092-3 Photovoltaics in buildings — Part 3: Evaluation methodology of SHGC for Building integrated photovoltaic modules with various designs
-
[특집-ISO/IEC JTC 1/SC 17 활동] 17. SC 37 Consultation on 3rd CD 29794-5… 2023년 11월23일까지 청취한 의견 종합2023년 10월25일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'SC 37 Consultation on 3rd CD 29794-5, Information technology — Biometric sample quality — Part 5- Face image data' 관련된 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안 장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서 'SC 37 Consultation on 3rd CD 29794-5, Information technology — Biometric sample quality — Part 5- Face image data'는 위원회 간사가 11월30일까지 의견을 청취했다.또한 ISO/IEC JTC 1/SC 37은 WG 3 "Biometric data interchange formats"의 'SC 37_N7594_Consultation on 3rd CD 29794-5, Information technology —Biometric sample quality — Part 5- Face image data'와 관련된 정보를 배포했다. SC 37이 "Biometrics"와 관련해 배포한 'Consultation on 3rd CD 29794-5, Information technology — Biometric sample quality — Part 5: Face image data' 문서는 3차 CD 상담을 위해 배포했다.- 이하 생략 -
-
[특집-기술위원회] TC 157 - 비체계적 피임약 및 성병(STI) 예방 콘돔(Non-systemic contraceptives and STI barrier prophylactics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.△1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 등도 포함된다.ISO/TC 157 비체계적 피임약 및 성병(STI) 예방 콘돔(Non-systemic contraceptives and STI barrier prophylactics)과 관련된 기술위원회는 TC 156과 마찬가지로 1974년 결성됐다. 사무국은 말레이시아 표준부(Department of Standards Malaysia, DSM)에서 맡고 있다.위원회는 페리스 프레데릭(Mr Feris Frederick)이 책임지고 있다. 현재 의장은 파리다 하님 압 하난(Dr Faridah Hanim Ab Hanan)로 임기는 2026년까지다. ISO 기술 프로그램 관리자는 페트리샤 쿡(Mme Patricia Cook), ISO 편집 관리자는 마사 카산토산(Mrs Martha Casantosan) 등으로 조사됐다.범위는 비체계적 피임약 및 성병(sexually transmitted infections, STI)을 예방하기 위한 콘돔의 표준화다.현재 ISO/TC 157 사무국의 직접적인 책임 하에 발행된 표준은 18개며 ISO/TC 15 사무국의 직접적인 책임 하에 개발중인 표준은 2개다. 참여하고 있는 회원은 24개국, 참관 회원은 28개국이다.□ ISO/TC 157 사무국의 직접적인 책임 하에 발행된 표준 18개 목록▷ISO 4074:2015 Natural rubber latex male condoms — Requirements and test methods▷ISO 7439:2023 Copper-bearing contraceptive intrauterine devices — Requirements and tests▷ISO 8009:2014 Mechanical contraceptives — Reusable natural and silicone rubber contraceptive diaphragms — Requirements and tests▷ISO 11249:2018 Copper-bearing intrauterine contraceptive devices — Guidance on the design, execution, analysis and interpretation of clinical studies▷ISO 16037:2002 Rubber condoms for clinical trials — Measurement of physical properties▷ISO 16037:2002/Amd 1:2011 Rubber condoms for clinical trials — Measurement of physical properties — Amendment 1▷ISO 16038:2017 Male condoms — Guidance on the use of ISO 4074 and ISO 23409 in the quality management of condoms▷ISO 19351:2019 Fallopian rings — Requirements and test methods▷ISO 19671:2018 Additional lubricants for male natural rubber latex condoms — Effect on condom strength▷ISO/TR 19969:2018 Guidance on sample handling for determination of bursting volume and pressure, and testing for freedom from holes for male condom▷ISO 23409:2011 Male condoms — Requirements and test methods for condoms made from synthetic materials▷ISO/TR 24484:2023 Female condoms — Use of ISO 25841 and the quality management of female condoms▷ISO 25841:2017 Female condoms — Requirements and test methods▷ISO 25841:2017/Amd 1:2020 Female condoms — Requirements and test methods — Amendment 1▷ISO 29941:2010 Condoms — Determination of nitrosamines migrating from natural rubber latex condoms □ ISO/TC 157 사무국의 직접적인 책임 하에 개발 중인 표준 2개 목록▷ISO/CD 4074 Natural rubber latex male condoms — Requirements and test methods▷ISO/TS 23148 Compatibility of lubricants with synthetic male condoms
-
[특집-기술위원회] TC 147 - 수질(Water quality)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127, △1969년 TC 130~136, △1970년 TC 137, TC 138, TC 142, TC 145 등도 포함된다.ISO/TC 147 수질(Water quality)과 관련된 기술위원회는 TC 146과 마찬가지로 1971년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 랠프 도미닉(Mr Ralph Dominik)이 책임지고 있다. 현재 의장은 크리스티나 포스터(Mrs Dr Christina Förster)으로 임기는 2024년까지다.ISO 기술 프로그램 관리자는 이사벨 베가(Ms Isabelle Vega), ISO 편집 관리자는 산잘리 자인(Ms Sanjali Jain) 등으로 조사됐다.범위는 용어 정의, 물 샘플링, 물 특성 측정 및 보고를 포함한 수질 분야의 표준화다. 단, 수질에 대한 수용성의 한계는 제외된다.현재 ISO/TC 147 사무국과 관련해 발행된 표준은 336개 이 중 사무국의 직접적인 책임 하에 발행된 표준은 2개다. ISO/TC 147 사무국과 관련해 개발 중인 표준은 37개며 참여하고 있는 회원은 37개국, 참관 회원은 54개국이다.□ ISO/TC 147 사무국의 직접적인 책임 하에 발행된 표준 2개 목록▷ISO 15839:2003 Water quality — On-line sensors/analysing equipment for water — Specifications and performance tests▷ISO 17381:2003 Water quality — Selection and application of ready-to-use test kit methods in water analysis□ ISO/TC 147 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 147/SC 1 Terminology ; 발행된 표준 1개, 개발 중인 표준 0개▷ISO/TC 147/SC 2 Physical, chemical and biochemical methods ; 발행된 표준 169개, 개발 중인 표준 15개▷ISO/TC 147/SC 3 Radioactivity measurements ; 발행된 표준 31개, 개발 중인 표준 7개▷ISO/TC 147/SC 4 Microbiological methods ; 발행된 표준 29 개발 중인 표준 6개▷ISO/TC 147/SC 5 Biological methods ; 발행된 표준 80 개발 중인 표준 5개▷ISO/TC 147/SC 6 Sampling (general methods) ; 발행된 표준 24 개발 중인 표준 4개
-
[특집-기술위원회] TC 146 - 공기질(Air quality)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다. 기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127, △1969년 TC 130~136, △1970년 TC 137, TC 138, TC 142, TC 145 등도 포함된다.ISO/TC 146 공기질(Air quality)과 관련된 기술위원회는 1971년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 엘리자베스 호젠-(Mrs Dr Elisabeth Hösen-Seul)이 책임지고 있다. 현재 의장은 제임스 S 웨버(Dr James S Webber)으로 임기는 2026년까지다.ISO 기술 프로그램 관리자는 타카이 타마호(Ms Tamaho Takai), ISO 편집 관리자는 산잘리 자인(Ms Sanjali Jain) 등으로 조사됐다.범위는 배출, 작업 공간 공기, 주변 공기, 실내 공기, 공기 품질 특성화를 위한 도구, 특히 대기 오염 물질(입자, 가스, 악취, 미생물)에 대한 측정 방법, 기상 매개변수, 측정 계획, 품질 보증(Quality Assurance, QA)/품질 관리(Quality Control, QC) 절차 등의 표준화다. 단, 대기 오염물질에 대한 한계값 설정, 클린룸의 공기질, 방사성 물질 등은 제외한다.현재 ISO/TC 146 사무국과 관련해 발행된 표준은 201개 이 중 사무국의 직접적인 책임 하에 발행된 표준은 2개다. ISO/TC 146 사무국과 관련해 개발 중인 표준은 37개이며 참여하고 있는 회원은 30개국, 참관 회원은 45개국이다.□ ISO/TC 146 사무국의 직접적인 책임 하에 발행된 표준 2개 목록▷ISO/AWI 16017-1 Indoor, ambient and workplace air — Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography — Part 1: Pumped sampling▷ISO/AWI 16017-2 Indoor, ambient and workplace air — Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography — Part 2: Diffusive sampling□ ISO/TC 146 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 146/SC 1 Stationary source emissions ; 발행된 표준 44개, 개발 중인 표준 6개▷ISO/TC 146/SC 2 Workplace atmospheres ; 발행된 표준 54개, 개발 중인 표준 10개▷ISO/TC 146/SC 3 Ambient atmospheres ; 발행된 표준 28개, 개발 중인 표준 3개▷ISO/TC 146/SC 4 General aspects 발행된 표준 12 개발 중인 표준 2개▷ISO/TC 146/SC 5 Meteorology 발행된 표준 10 개발 중인 표준 4개▷ISO/TC 146/SC 6 Indoor air 발행된 표준 53 개발 중인 표준 10개
-
[특집-기술위원회] TC 130 - 그래픽 기술(Graphic technology)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127 등도 포함된다.ISO/TC 130 그래픽 기술(Graphic technology)과 관련된 기술위원회는 1969년 결성됐다. 사무국은 중국 국가표준화관리위원(国家标准化管理委员会, Standardization Administration of China, SAC)에서 맡고 있다.위원회는 메이팡 리(Ms Meifang Li)가 책임지고 있다. 현재 의장은 펑페이 짜오(Mr Pengfei Zhao)로 임기는 2023년까지다.ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 마사 카산토산(Mrs Martha Casantosan) 등으로 조사됐다.범위는 인쇄 및 그래픽 기술 분야의 표준화를 다루고 있다. 이 분야는 그래픽 요소(이미지, 텍스트, 라인 아트, 패턴 등)가 생성, 조작, 조립, 전달되고 최종적으로 디지털 제품으로 전자적으로 전달되거나 잉크, 토너 및 기타를 사용해 물리적으로 기판에 전달되는 프로세스의 모든 단계를 다룬다. 마킹 또는 기능성 재료를 생산하고 최종 응용 분야의 요구에 따라 마감 처리된다.ISO/TC 130 표준에는 용어, 시각적 외관 및 제품 품질 평가, 데이터 교환, 프로세스 제어, 관리, 적합성 평가, 환경에 대한 영향 등이 포함되지만 이에 국한되지는 않는다. 뿐만 아니라 관련 재료, 장비 및 시스템에 대한 요구 사항 및 테스트도 수용한다.참고로 ISO/TC 42, TC 6, TC 256, TC 35, IEC/TC 100 및 ISO/IEC JTC 1/SC 28과 같은 다른 TC/SC와 범위가 실제 또는 잠재적으로 중복되는 경우 관련 TC와의 연락 또는 JWG를 통한 조정은 유지되거나 적극적으로 추진돼야 한다.현재 ISO/TC 130 사무국과 관련해 발행된 표준은 115개며 ISO/TC 130 사무국과 관련해 개발 중인 표준은 15개다. 참여하고 있는 회원은 21개국, 참관 회원은 22개국이다.□ ISO/TC 130 사무국 분과위원회(Subcommittee)의 책임 하에 발행된 표준 115개 중 15개 목록▷ISO 2834-1:2020 Graphic technology — Laboratory preparation of test prints — Part 1: Paste inks▷ISO 2834-2:2022 Graphic technology — Laboratory preparation of test prints — Part 2: Liquid printing inks▷ISO 2834-3:2008 Graphic technology — Laboratory preparation of test prints — Part 3: Screen printing inks▷ISO 2836:2021 Graphic technology — Prints and printing inks — Assessment of resistance of prints to various agents▷ISO 2846-1:2017 Graphic technology — Colour and transparency of printing ink sets for four-colour printing — Part 1: Sheet-fed and heat-set web offset lithographic printing▷ISO 2846-2:2007 Graphic technology — Colour and transparency of printing ink sets for four-colour printing — Part 2: Coldset offset lithographic printing▷ISO 5776:2022 Graphic technology — Symbols for text proof correction▷ISO/TS 10128:2009 Graphic technology — Methods of adjustment of the colour reproduction of a printing system to match a set of characterization data▷ISO 11084-1:1993 Graphic technology — Register systems for photographic materials, foils and paper — Part 1: Three-pin systems▷ISO 11084-2:2006 Graphic technology — Register systems for photographic materials, foils and paper — Part 2: Register pin systems for plate making▷ISO 12040:1997 Graphic technology — Prints and printing inks — Assessment of light fastness using filtered xenon arc light▷ISO 12218:1997 Graphic technology — Process control — Offset platemaking▷ISO 12632:2015 Graphic technology — Ink, paper and labels — Requirements on hot alkali penetration and resistance▷ISO 12634:2017 Graphic technology — Determination of tack of paste inks and vehicles by a rotary tackmeter▷ISO 12635:2021 Graphic technology — Plates for offset printing — Dimensions□ ISO/TC 130 사무국 분과위원회(Subcommittee)의 책임 하에 개발 중인 표준 15개 목록▷ISO/DTS 10128 Graphic technology — Methods of adjustment of the colour reproduction of a printing system to match a set of characterization data▷ISO/DIS 12641-1 Graphic technology — Prepress digital data exchange — Colour targets for input scanner calibration — Part 1: Colour targets for input scanner calibration▷ISO/FDIS 12643-1.2 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 1: General requirements▷ISO/FDIS 12643-2.2 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 2: Prepress and press equipment and systems▷ISO/FDIS 12643-3 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 3: Binding and finishing equipment and systems▷ISO/FDIS 12643-4 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 4: Converting equipment and systems▷ISO/FDIS 12643-5 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 5: Manually-fed stand-alone platen presses▷ISO/DIS 12647-2 Graphic technology — Process control for the production of half-tone colour separations, proof and production prints — Part 2: Offset lithographic processes▷ISO/AWI 15076-2 Image technology colour management — Architecture, profile format and data structure — Part 2: Based on ICC.1:2022▷ISO/DIS 15339-1 Graphic technology — Printing from digital data across multiple technologies — Part 1: Principles▷ISO/AWI TS 18621-22 Graphic technology — Image quality evaluation methods for printed matter — Part 22: Evaluation of colour graininess▷ISO/DTS 18621-31 Graphic technology — Image quality evaluation methods for printed matter — Part 31: Evaluation of the perceived resolution of printing systems with the Contrast–Resolution chart▷ISO/AWI 19307 Graphic Technology — Measurement and one-parameter representation of translucency▷ISO/CD TR 23805 Graphic technology — Dry back calculation for offset printing process▷ISO/FDIS 24487 Graphic technology — Processless lithographic plates — Evaluation methods for characteristics and performance□ ISO/TC 130 사무국의 작업그룹(Working Group, WG) 현황▷ISO/TC 130/JWG 7 Joint TC 130 - ICC WG: colour management▷ISO/TC 130/JWG 14 Joint TC 130 - TC 42 - ISO/IEC JTC 1/SC 28 WG: Print quality measurement methods▷ISO/TC 130/TF 3 Communications▷ISO/TC 130/WG 1 Terminology▷ISO/TC 130/WG 2 Prepress data exchange▷ISO/TC 130/WG 3 Process control and related metrology▷ISO/TC 130/WG 4 Media and materials▷ISO/TC 130/WG 5 Ergonomics - Safety▷ISO/TC 130/WG 10 Management of security printing processes▷ISO/TC 130/WG 11 Environmental impact of graphic technology▷ISO/TC 130/WG 12 Postpress