검색결과
-
[특집-기술위원회] TC 192 - 가스 터빈(Gas turbines)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 등이 있다.ISO/TC 192 가스 터빈(Gas turbines)과 관련된 기술위원회는1988년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 크리스토퍼 다빌라-아폰테(Mr Christopher Davila-Aponte)이 책임지고 있다. 현재 의장은 조지 랭튼(Mr George Langton)이며 임기는 2024년 말까지다. ISO 기술 프로그램 관리자는 모니카 이비도(Ms Monica Ibido), ISO 편집 관리자는 루시 커크(Ms Lucy Kirk)등으로 조사됐다.범위는 단순 터빈 사이클, 복합 사이클 시스템, 정의, 조달, 수용, 성능, 환경(가스터빈 자체 및 외부 환경에 대한) 및 테스트 방법 등을 포함해 가스 터빈 설계, 적용, 안전, 설치, 운영 및 유지보수의 모든 분야의 표준화다. 표준화에서는 재생 에너지 생산의 변동을 보상하기 위해 재생 가능한 영역 지원하기 위해 가스 터빈이 구현되는 것을 고려한다. 표준화는 가스 터빈 기술이 광범위한 기체 및 액체 연료를 사용해 작동한다는 점을 고려한다.ISO/TC 192는 모든 유형의 가스 터빈에 대한 수평적 표준을 준비하는 일을 담당한다. 항공가스터빈 엔진에 대한 작업은 주요 책임을 맡은 기술위원회와 협력해 수행돼야 한다. 참고로 ISO/TC 20은 항공우주을 위한 가스 터빈의 특정 응용과 관련한 표준을 준비하는 1차적인 책임을 진다.현재 ISO/TC 192 사무국의 직접적인 책임하에 발행된 표준은 18개며 ISO/TC 192 사무국의 직접적인 책임 하에 개발 중인 표준은 3개다. 참여하고 있는 회원은 15개국, 참관 회원은 12개국이다.□ ISO/TC 192 사무국의 직접적인 책임 하에 발행된 표준 15개 목록▷ISO 2314:2009 Gas turbines — Acceptance tests▷ISO 3977-1:1997 Gas turbines — Procurement — Part 1: General introduction and definitions▷ISO 3977-2:2023 Gas turbines — Procurement — Part 2: Standard reference conditions and ratings▷ISO 3977-3:2004 Gas turbines — Procurement — Part 3: Design requirements▷ISO 3977-4:2002 Gas turbines — Procurement — Part 4: Fuels and environment▷ISO 3977-8:2002 Gas turbines — Procurement — Part 8: Inspection, testing, installation and commissioning▷ISO 3977-9:1999 Gas turbines — Procurement — Part 9: Reliability, availability, maintainability and safety▷ISO 10494:2018 Turbines and turbine sets — Measurement of emitted airborne noise — Engineering/survey method▷ISO 11042-1:1996 Gas turbines — Exhaust gas emission — Part 1: Measurement and evaluation▷ISO 11042-2:1996 Gas turbines — Exhaust gas emission — Part 2: Automated emission monitoring▷ISO 11086:1996 Gas turbines — Vocabulary▷ISO 18888:2017 Gas turbine combined cycle power plants — Thermal performance tests▷ISO 19372:2015 Microturbines applications — Safety▷ISO 19859:2016 Gas turbine applications — Requirements for power generation▷ISO 19860:2005 Gas turbines — Data acquisition and trend monitoring system requirements for gas turbine installations□ ISO/TC 192 사무국의 직접적인 책임 하에 개발 중인 표준 3개 목록▷ISO/AWI 2314 Gas turbines — Acceptance tests▷ISO/FDIS 3977-9 Gas turbines — Procurement — Part 9: Reliability, availability and maintainability▷ISO/WD 19372 Microturbines applications — Safety
-
[특집-기술위원회] TC 189 - 세라믹 타일(Ceramic tile)… 바닥재 및 벽면 마감재에 사용되는 세라믹 타일의 표준화스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186, △1984년 TC 188등이 있다.ISO/TC 189 세라믹 타일(Ceramic tile)과 관련된 기술위원회는 1985년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 존 P. 샌더스(Dr John P. Sanders)이 책임지고 있다. 현재 의장은 노아 치티(Mr Noah Chitty)이며 임기는 2024년까지다.ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 루시 커크(Ms Lucy Kirk)등으로 조사됐다. 범위는 일반적으로 바닥재 및 벽면 마감재에 사용되는 세라믹 타일의 표준화다.현재 ISO/TC 189 사무국의 직접적인 책임 하에 발행된 표준은 35개며 ISO/TC 189 사무국의 직접적인 책임 하에 개발 중인 표준은 12개다. 참여하고 있는 회원은 35개국, 참관 회원은 25개국이다.□ ISO/TC 189 사무국의 직접적인 책임 하에 발행된 표준 35개 중 15개 목록▷ISO 10545-1:2014 Ceramic tiles — Part 1: Sampling and basis for acceptance▷ISO 10545-2:2018 Ceramic tiles — Part 2: Determination of dimensions and surface quality▷ISO 10545-3:2018 Ceramic tiles — Part 3: Determination of water absorption, apparent porosity, apparent relative density and bulk density▷ISO 10545-4:2019 Ceramic tiles — Part 4: Determination of modulus of rupture and breaking strength▷ISO 10545-5:1996 Ceramic tiles — Part 5: Determination of impact resistance by measurement of coefficient of restitution▷ISO 10545-5:1996/Cor 1:1997 Ceramic tiles — Part 5: Determination of impact resistance by measurement of coefficient of restitution — Technical Corrigendum 1▷ISO 10545-6:2010 Ceramic tiles — Part 6: Determination of resistance to deep abrasion for unglazed tiles▷ISO 10545-7:1996 Ceramic tiles — Part 7: Determination of resistance to surface abrasion for glazed tiles▷ISO 10545-8:2014 Ceramic tiles — Part 8: Determination of linear thermal expansion▷ISO 10545-9:2013 Ceramic tiles — Part 9: Determination of resistance to thermal shock▷ISO 10545-10:2021 Ceramic tiles — Part 10: Determination of moisture expansion▷ISO 10545-11:1994 Ceramic tiles — Part 11: Determination of crazing resistance for glazed tiles▷ISO 10545-12:1995 Ceramic tiles — Part 12: Determination of frost resistance▷ISO 10545-12:1995/Cor 1:1997 Ceramic tiles — Part 12: Determination of frost resistance — Technical Corrigendum 1▷ISO 10545-13:2016 Ceramic tiles — Part 13: Determination of chemical resistance□ ISO/TC 189 사무국의 직접적인 책임 하에 개발 중인 표준 12개 목록▷ISO/CD 10545-22 Ceramic tiles — Part 22: Determination of resistance to wear with a multi-attribute method▷ISO/CD 10545-23 Ceramic tiles — Part 23: Determination of elastic modulus for substrates and glaze layer▷ISO/WD 10545-24 Ceramic tiles — Part 24: Tensile adhesion strength of multilayer tiles and tile adhesives▷ISO/AWI 10545-25 Ceramic tiles — Part 25: Determination of reverse staining resistance▷ISO/AWI 13007-1 Ceramic tiles — Grouts and adhesives — Part 1: Terms, definitions and specifications for adhesives▷ISO/AWI 13007-3 Ceramic tiles — Grouts and adhesives — Part 3: Terms, definitions and specifications for grouts▷ISO/AWI 13007-7 Ceramic tiles — Grouts and adhesives — Part 7: Sound dampening materials for use beneath ceramic tiling bonded with adhesives — Requirements, test methods, evaluation of conformity, classification and designation▷ISO/AWI TR 17870-2 Ceramic tiles — Guidelines for installation — Part 2: Installation of thin ceramic wall and floor tiles and panels▷ISO/AWI 17889-3 Ceramic tiling systems — Sustainability for ceramic tiles and installation materials — Part 3: Guidelines for the application and verification of ISO 17889-1 and 17889-2▷ISO/WD 20355 Quantitative determination of antiviral activity of ceramic tile surfaces and survival of viruses on ceramic surfaces — Test methods — Ceramic tile surfaces with incorporated antiviral agents▷ISO/WD 20356 Quantitative determination of antifungal activity of ceramic tile surfaces — Test methods — Ceramic tile surfaces with incorporated antifungal agents▷ISO/WD 22267-1 Ceramic Tiling Systems — Embodied Carbon — Part 1: Calculation of Embodied Carbon of Ceramic Tile
-
[특집-기술위원회] TC 188 - 소형선박(Small craft)… 선체 길이가 최대 24미터인 레저 선박 및 유사한 장비를 사용하는 기타 소형 선박스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186등이 있다.ISO/TC 188 소형선박(Small craft)과 관련된 기술위원회는 1984년 결성됐다. 사무국은 스웨덴 국립표준청(Svenska institutet för standarder, SIS)에서 맡고 있다.위원회는 아네트 에릭슨(Ms Anette Eriksson)이 책임지고 있다. 현재 의장은 크레이그 숄튼(Mr Craig Scholten)이며 임기는 2026년까지다.ISO 기술 프로그램 관리자는 메르세 페레 에르난데스(Mme Mercè Ferrés Hernández) ISO 편집 관리자는 니콜라 페루(Ms Nicola Perou) 등으로 조사됐다.범위는 선체 길이가 최대 24미터인 레저 선박 및 유사한 장비를 사용하는 기타 소형 선박의 장비 및 구조 세부 사항의 표준화다. 단, ISO/TC 8이 다루고 있는 구명정 및 구명 장비는 제외한다.현재 ISO/TC 188 사무국과 관련해 발행된 표준은 96개며 ISO/TC 188 사무국의 직접적인 책임 하에 발행된 표준은 82개다.ISO/TC 188 사무국과 관련해 개발 중인 표준은 16개며 ISO/TC 188 사무국의 직접적인 책임 하에 개발 중인 표준은 12개다. 참여하고 있는 회원은 22개국, 참관 회원은 23개국이다.□ ISO/TC 188 사무국의 직접적인 책임 하에 발행된 표준 82개 중 15개 목록▷ISO 4566:1992 Small craft with inboard engine — Propeller shaft ends and bosses with 1:10 taper▷ISO 6017:2024 Small craft — Automatic watertight ventilation shutdown system▷ISO 6185-1:2001 Inflatable boats — Part 1: Boats with a maximum motor power rating of 4,5 kW▷ISO 6185-2:2001 Inflatable boats — Part 2: Boats with a maximum motor power rating of 4,5 kW to 15 kW inclusive▷ISO 6185-3:2014 Inflatable boats — Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater▷ISO 6185-4:2011 Inflatable boats — Part 4: Boats with a hull length of between 8 m and 24 m with a motor power rating of 15 kW and greater▷ISO 7840:2021 Small craft — Fire-resistant fuel hoses▷ISO 8099-1:2018 Small craft — Waste systems — Part 1: Waste water retention▷ISO 8099-2:2020 Small craft — Waste systems — Part 2: Sewage treatment systems▷ISO 8469:2021 Small craft — Non-fire-resistant fuel hoses▷ISO 8665:2006 Small craft — Marine propulsion reciprocating internal combustion engines — Power measurements and declarations▷ISO 8666:2020 Small craft — Principal data▷ISO 8845:1994 Small craft with inboard engine — Propeller shaft ends and bosses with 1:16 taper▷ISO 8845:1994/Cor 1:1995 Small craft with inboard engine — Propeller shaft ends and bosses with 1:16 taper — Technical Corrigendum 1▷ISO 8846:1990 Small craft — Electrical devices — Protection against ignition of surrounding flammable gases□ ISO/TC 188 사무국의 직접적인 책임 하에 개발 중인 표준 12개 목록▷ISO/FDIS 6185-3 Inflatable boats — Part 3: Boats with a length of the hull less than 8 m with a motor power rating of 15 kW and greater▷ISO/FDIS 8665-2 Small craft — Power measurements and declarations — Part 2: Electric marine propulsion▷ISO/DIS 8846 Small craft — Electrical devices — Protection against ignition of surrounding flammable gases▷ISO/DIS 10239.2 Small craft — Liquefied petroleum gas (LPG) systems▷ISO 11812:2020/DAmd 1 Small craft — Watertight or quick-draining recesses and cockpits — Amendment 1▷ISO/CD 12215-9 Small craft — Hull construction and scantlings — Part 9: Sailing craft appendages▷ISO/AWI 12217-1 Small craft — Stability and buoyancy assessment and categorization — Part 1: Non-sailing boats of hull length greater than or equal to 6 m▷ISO/AWI 12217-2 Small craft — Stability and buoyancy assessment and categorization — Part 2: Sailing boats of hull length greater than or equal to 6 m▷ISO/AWI 12217-3 Small craft — Stability and buoyancy assessment and categorization — Part 3: Boats of hull length less than 6 m▷ISO/FDIS 15085 Small craft — Protection from falling overboard and means of reboarding▷ISO/DIS 16315 Small craft — Electrical systems used for electrical propulsion▷ISO/CD 23625 Small craft — Lithium-ion batteries□ ISO/TC 188 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 188/SC 1 Personal safety equipment ; 발행된 표준 14개, 개발 중인 표준 4개
-
식약처, ‘첨단 동물대체시험법 표준화 국제심포지엄’ 개최식품의약품안전처 소속 식품의약품안전평가원은 첨단 동물대체시험 연구와 정책 동향을 공유하고 동물대체시험 표준화 인프라를 구축하기 위해 22일 서울 중구 신라호텔에서 ‘첨단 동물대체시험법 표준화 국제심포지엄’을 개최한다고 밝혔다. 이번 국제심포지엄이 첨단 바이오 기술 기반 동물대체시험 표준화에 도움이 될 것으로 기대된다. 이번 국제심포지엄에서는 ▲미국 FDA, NIEHS 첨단 동물대체시험 개발 현황 및 규제적용 ▲OECD 첨단 동물대체시험 활용 및 전망 ▲OECD 첨단 동물대체시험 기반 가이드라인 및 추진 프로젝트 소개 ▲한국동물대체시험검증센터(KoCVAM) 및 국내 동물대체시험 규제적용 등에 대한 전문가 발표가 있을 예정이다. NIEHS(National Institute of Environmental Health Science)는 첨단 동물대체시험 연구 및 인체·환경 보건 등을 담당하는 미국 규제기관이다. 관심 있는 누구나 사전등록(https://naver.me/xSNH1Djj) 후 이번 국제심포지엄에 참석할 수 있으며 사전등록은 16일까지 가능하다. 식약처 관계자는 “이번 국제심포지엄이 오가노이드 등 첨단 바이오 기술 기반 동물대체시험 표준화에 도움을 줄 것으로 기대한다”며 “앞으로도 산업계, 학계, 관련 부처 등의 다양한 의견을 청취하고 협력하는 등 국내 동물대체시험 분야 연구 개발을 적극 지원할 계획”이라고 밝혔다.
-
[특집-기술위원회] TC 185 - 과도한 압력으로부터 보호하기 위한 안전장치(Safety devices for protection against excessive pressure)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 등이 있다.ISO/TC 185 과도한 압력으로부터 보호하기 위한 안전 장치(Safety devices for protection against excessive pressure)와 관련된 기술위원회는 TC 183, TC 184와 마찬가지로 1983년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 콜린 로드리게스(Ms Colleen Rodrigues)가 책임지고 있으며 현재 의장은 위르겐 슈미트(Mr Prof. Dr.-Ing Jürgen Schmidt)이며 임기는 2024년까지다.ISO 기술 프로그램 관리자는 샐리 스윙우드(Ms Sally Swingewood), ISO 편집 관리자는 루시 커크(Ms Lucy Kirk) 등으로 조사됐다.범위는 과도한 내부 및 외부 압력으로부터 보호하기 위한 안전 장치 분야의 표준화다. 단 ISO/TC 138의 책임 하에 있는 주로 플라스틱으로 만들어진 밸브, ISO/TC 131의 책임 하에 있는 주로 유체 동력 시스템에 사용하도록 고안된 구성 요소들은 제외한다.현재 ISO/TC 185의 직접적인 책임 하에 발행된 표준은 12개며 ISO/TC 185의 직접적인 책임 하에 개발 중인 표준은 2개다. 참여하고 있는 회원은 13개국, 참관 회원은 22개국이다.□ ISO/TC 185 사무국의 직접적인 책임 하에 발행된 표준 12개 목록▷ISO 4126-1:2013 Safety devices for protection against excessive pressure — Part 1: Safety valves▷ISO 4126-1:2013/Amd 1:2016 Safety devices for protection against excessive pressure — Part 1: Safety valves — Amendment 1▷ISO 4126-2:2018 Safety devices for protection against excessive pressure — Part 2: Bursting disc safety devices▷ISO 4126-3:2020 Safety devices for protection against excessive pressure — Part 3: Safety valves and bursting disc safety devices in combination▷ISO 4126-4:2013 Safety devices for protection against excessive pressure — Part 4: Pilot operated safety valves▷ISO 4126-5:2013 Safety devices for protection against excessive pressure — Part 5: Controlled safety pressure relief systems (CSPRS)▷ISO 4126-5:2013/Amd 1:2016 Safety devices for protection against excessive pressure — Part 5: Controlled safety pressure relief systems (CSPRS) — Amendment 1▷ISO 4126-6:2014 Safety devices for protection against excessive pressure — Part 6: Application, selection and installation of bursting disc safety devices▷ISO 4126-7:2013 Safety devices for protection against excessive pressure — Part 7: Common data▷ISO 4126-7:2013/Amd 1:2016 Safety devices for protection against excessive pressure — Part 7: Common data — Amendment 1▷ISO 4126-9:2008 Safety devices for protection against excessive pressure — Part 9: Application and installation of safety devices excluding stand-alone bursting disc safety devices▷ISO 4126-10:2010 Safety devices for protection against excessive pressure — Part 10: Sizing of safety valves for gas/liquid two-phase flow□ ISO/TC 185 사무국의 직접적인 책임 하에 개발 중인 표준 2개 목록▷ISO 4126-10 Safety devices for protection against excessive pressure — Part 10: Sizing of safety valves and bursting discs for gas/liquid two-phase flow▷ISO/AWI 4126-11 Safety devices for protection against excessive pressure — Part 11: Performance Testing
-
[특집-기술위원회] TC 173 - 보조 용품(Assistive products)… 개인의 줄어든 능력을 보정하는데 도움을 주기 위한 보조 용품 및 관련 서비스스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 등도 포함된다.ISO/TC 173 보조 용품(Assistive products)과 관련된 기술위원회는 TC 171, TC 172와 마찬가지로 1978년 결성됐다. 사무국은 스웨덴 표준연구소(Swedish Institute for Standards, SIS)에서 맡고 있다.위원회는 조아킴 포크(Mr Joakim Falk)가 책임지고 있으며 현재 의장은 마리타 브런딘(Ms Marita Brundin)이며 임기는 2025년까지다. ISO 기술 프로그램 관리자는 마호 타카하시(Mme Maho Takahashi), ISO 편집 관리자는 발레리아 아가멤논(Ms Valeria Agamennone) 등으로 조사됐다.범위는 개인의 줄어든 능력을 보정하는데 도움을 주기 위한 보조 용품 및 관련 서비스 분야의 표준화다. 단 기타 기술위원회 및 시스템위원회에서 다루고 있는 보조용품들은 제외한다.교통 수단(ISO/TC 8, 20, 22), 건물 건축(ISO/TC 59), 가구(ISO/TC 136), 수술용 임플란트(ISO/TC 150), 보철물 및 교정 장치(ISO/TC 150)에 대한 접근 /TC 168), 광학 및 포토닉스(ISO/TC 172), 전기 안전(IEC/TC 62), 보청기(IEC/TC 29), ICT 기술(JTC 1) 및 인체공학에서 다루는 설계 원리(ISO/TC 159) 및 적극적 생활 지원(IEC SyCAAL) 등이 포함된다.현재 ISO/TC 173 사무국과 관련해 발행된 표준은 95개며 이 중 ISO/TC 173 사무국의 직접적인 책임 하에 발행된 표준은 24개다.ISO/TC 173 사무국과 관련해 개발 중인 표준은 22개며 ISO/TC 173 사무국의 직접적인 책임 하에 개발 중인 표준은 11개다. 참여하고 있는 회원은 26개국, 참관 회원은 29개국이다.□ ISO/TC 173 사무국의 직접적인 책임 하에 발행된 표준 24개 중 15개 목록▷ISO 10535:2021 Assistive products — Hoists for the transfer of persons — Requirements and test methods▷ISO 11199-1:2021 Assistive products for walking manipulated by both arms — Requirements and test methods — Part 1: Walking frames▷ISO 11199-2:2021 Assistive products for walking manipulated by both arms — Requirements and test methods — Part 2: Rollators▷ISO 11199-3:2005 Walking aids manipulated by both arms — Requirements and test methods — Part 3: Walking tables▷ISO 11334-1:2007 Assistive products for walking manipulated by one arm — Requirements and test methods — Part 1: Elbow crutches▷ISO 11334-4:1999 Walking aids manipulated by one arm — Requirements and test methods — Part 4: Walking sticks with three or more legs▷ISO/TR 11548-1:2001 Communication aids for blind persons — Identifiers, names and assignation to coded character sets for 8-dot Braille characters — Part 1: General guidelines for Braille identifiers and shift marks▷ISO/TR 11548-2:2001 Communication aids for blind persons — Identifiers, names and assignation to coded character sets for 8-dot Braille characters — Part 2: Latin alphabet based character sets▷ISO 17966:2016 Assistive products for personal hygiene that support users — Requirements and test methods▷ISO 19894:2019 Walking trolleys — Requirements and test methods▷ISO 20342-1:2022 Assistive products for tissue integrity when lying down — Part 1: General requirements▷ISO/TR 20342-7:2021 Assistive products for tissue integrity when lying down — Part 7: Foam properties, characteristics and performance▷ISO/TS 20342-10:2022 Assistive products for tissue integrity when lying down — Part 10: Guidance to cleaning, disinfecting and care of polyurethane APTI covers▷ISO 21801-1:2020 Cognitive accessibility — Part 1: General guidelines▷ISO 21801-2:2022 Cognitive accessibility — Part 2: Reporting□ ISO/TC 173 사무국의 직접적인 책임 하에 개발 중인 표준 11개 목록▷ISO 11199-2:2021/DAmd 1 Assistive products for walking manipulated by both arms — Requirements and test methods — Part 2: Rollators — Amendment 1: Eliminate brake requirements in 6.5 Structure requirements▷ISO/DIS 11334-4 Assistive products for walking, manipulated by one arm — Requirements and test methods — Part 4: Walking sticks with three or more legs▷ISO/CD 17966 Assistive products for toileting, bathing and showering — Requirements and test methods▷ISO/AWI TR 20342-2 Assistive products for tissue integrity when lying down — Part 2: Microclimate▷ISO/CD 20342-3 Assistive products for tissue integrity when lying down — Part 3: Strength and impact▷ISO/CD 20342-4 Assistive products for tissue integrity when lying down — Part 4: Durability▷ISO/DIS 20342-5 Assistive products for tissue integrity when lying down — Part 5: Resistance to cleaning and disinfection▷ISO/AWI 20342-6 Assistive products for tissue integrity when lying down — Part 6: Horizontal stiffness▷ISO/CD 20342-8 Assistive products for tissue integrity when lying down — Part 8: Pressure distribution▷IEC/DIS 80601-2-52 Medical electrical equipment — Part 2-52: Particular requirements for the basic safety and essential performance of medical beds▷IEC/DIS 80601-2-89 Medical electrical equipment — Part 2-89: Particular requirements for the basic safety and essential performance of medical beds for children□ ISO/TC 173 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 173/SC 1 Wheelchairs ; 발행된 표준 41개, 개발 중인 표준 6개▷ISO/TC 173/SC 2 Classification and terminology ; 발행된 표준 1개, 개발 중인 표준 0개▷ISO/TC 173/SC 3 Aids for ostomy and incontinence ; 발행된 표준 23개, 개발 중인 표준 4개▷ISO/TC 173/SC 7 Assistive products for persons with impaired sensory functions ; 발행된 표준 6개, 개발 중인 표준 1개
-
[특집-기술위원회] TC 163 - 건축환경의 열 성능 및 에너지 사용(Thermal performance and energy use in the built environment)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.△1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 등도 포함된다.ISO/TC 163 건축환경의 열 성능 및 에너지 사용(Thermal performance and energy use in the built environment)과 관련된 기술위원회는 TC 162와 마찬가지로 1975년 결성됐다. 사무국은 스웨덴 표준협회(Swedish Institute for Standards, SIS)에서 맡고 있다.위원회는 벵트 리드슈테트(Mr Bengt Rydstedt)가 책임지고 있으며 현재 의장은 예스퍼 아르프비드손(Mr Jesper Arfvidsson)다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje) 등으로 조사됐다. 범위는 다음과 같은 건축 및 토목 공학 작업 분야의 표준화다. - 신축 및 기존 건물 전체를 포함한 재료, 제품, 부품, 요소 및 시스템의 열 및 습열 성능과 기술 건물 시스템과의 상호 작용 - 건물에 설치된 장비의 단열을 포함해 건축 및 산업용 단열재, 제품 및 시스템 - 열 및 습기 전달, 온도 및 습기 조건에 대한 테스트 및 계산 방법 - 산업 건축 환경을 포함한 건물의 에너지 사용에 대한 테스트 및 계산 방법 - 건물의 냉난방 부하에 대한 테스트 및 계산 방법 - 일광, 환기 및 공기 침투에 대한 테스트 및 계산 방법 - 건물 및 건물 구성요소의 열, 습열 및 에너지 성능에 대한 현장 테스트 방법, 기후 데이터를 포함한 계산을 위한 입력 데이터 - 관련 테스트 방법 및 적합성 기준이 포함된 단열재, 제품 및 시스템 사양 - 용어 - ISO 내 열 및 습열 성능에 대한 작업의 일반적인 검토 및 조정단, 건축 환경 설계(ISO/TC 205), 새로운 건물 및 개조 설계에 적용하기 위한 건물 환경 장비의 성능을 테스트하고 평가하는 방법(ISO/TC 205), 일광, 환기 및 공기 침투를 위한 설계 방법 및 기준(ISO/TC 205) 등은 제외한다.ISO/TC163/WG4 공동 작업 그룹 'TC 163 및 TC 205 에너지 성능'을 통해 ISO/TC 205와의 긴밀한 협력을 통해 건물 개조뿐 아니라 신규 건물과 기존 건물의 에너지 성능에 대한 전체적인 평가를 표준화하고 있다.ISO/TC163/WG4 공동 작업 그룹은 용어 및 정의, 건물 및 기술 시스템의 시스템 경계, 다음을 고려한 건물의 전반적인 에너지 성능 평가 등을 표준화한다. - 건축 요소의 에너지 성능 - 건물 관련 시스템(난방, 냉방, 가정용 온수, 환기, 조명, 시스템 제어, 운송 및 기타 에너지 관련 시스템) - 실내 및 실외 조건 - 지역 에너지 생산(현장 및 지역 수준) - (사용) 에너지원(재생 가능 포함) - 건물 시운전 - 전반적인 에너지 효율 평가 - 건축물의 에너지성능을 표현하는 수단 및 에너지성능 인증 등현재 ISO/TC 163 사무국과 관련해 발행된 표준은 152개며 이중 사무국의 직접적인 책임 하에 발행된 표준은 15개다. ISO/TC 16 사무국과 관련해 개발 중인 표준은 15개며 참여하고 있는 회원은 29개국, 참관 회원은 35개국이다.□ ISO/TC 163 사무국의 직접적인 책임 하에 발행된 표준 15개 목록▷ISO 7345:2018 Thermal performance of buildings and building components — Physical quantities and definitions▷ISO 9229:2020 Thermal insulation — Vocabulary▷ISO 9251:1987 Thermal insulation — Heat transfer conditions and properties of materials — Vocabulary▷ISO 9288:2022 Thermal insulation — Heat transfer by radiation — Vocabulary▷ISO 9346:2007 Hygrothermal performance of buildings and building materials — Physical quantities for mass transfer — Vocabulary▷ISO 12655:2013 Energy performance of buildings — Presentation of measured energy use of buildings▷ISO 17772-1:2017 Energy performance of buildings — Indoor environmental quality — Part 1: Indoor environmental input parameters for the design and assessment of energy performance of buildings▷ISO/TR 17772-2:2018 Energy performance of buildings — Overall energy performance assessment procedures — Part 2: Guideline for using indoor environmental input parameters for the design and assessment of energy performance of buildings▷ISO 18523-1:2016 Energy performance of buildings — Schedule and condition of building, zone and space usage for energy calculation — Part 1: Non-residential buildings▷ISO 18523-2:2018 Energy performance of buildings — Schedule and condition of building, zone and space usage for energy calculation — Part 2: Residential buildings▷ISO 52000-1:2017 Energy performance of buildings — Overarching EPB assessment — Part 1: General framework and procedures▷ISO/TR 52000-2:2017 Energy performance of buildings — Overarching EPB assessment — Part 2: Explanation and justification of ISO 52000-1▷ISO 52000-3:2023 Energy performance of buildings — Overarching EPB assessment — Part 3: General principles for determination and reporting of primary energy factors (PEF) and CO2 emission coefficients▷ISO 52003-1:2017 Energy performance of buildings — Indicators, requirements, ratings and certificates — Part 1: General aspects and application to the overall energy performance▷ISO/TR 52003-2:2017 Energy performance of buildings — Indicators, requirements, ratings and certificates — Part 2: Explanation and justification of ISO 52003-1□ ISO/TC 163 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 163/SC 1 Test and measurement methods ; 발행된 표준 76개, 개발 중인 표준 4개▷ISO/TC 163/SC 2 Calculation methods ; 발행된 표준 40개, 개발 중인 표준 3개▷ISO/TC 163/SC 3 Thermal insulation products, components and systems ; 발행된 표준 21개, 개발 중인 표준 8개
-
[기획-디지털 ID 기술] (77)Abcd테크놀로지, '뉴럴 블록체인' 명칭의 유럽 특허 등록(EP 3881491)스위스 로잔 연방공과대학(Swiss Federal Institute of Technology Lausanne)으로부터 분사된 기업 Abcd테크놀로지(Abcd Technology)에 따르면 2023년 1월4일 '뉴럴 블록체인(Neural Blockchain)' 명칭의 유럽 특허(EP 3881491)가 등록됐다.본 유럽 등록 특허(EP 388149)는 모출원인 PCT국제출원(WO2020-099629)을 기초로 유럽 특허청에 의해 심사받았다.PCT국제출원(WO2020-099629)은 2018년 11월16일 최초 출원된 이탈리아 특허(IT 102018000010379)을 기초로 2019년 11월15일 PCT 국제출원됐다.패밀리 특허로 인도 특허(IN 202147021437), 모로코 특허(MA 54217), 유라시아 특허(EA 202190845), 중국 특허(CN 113039748), 미국 특허(US 2022/0006658)가 심사 중이다.본 유럽 등록 특허(EP 388149)는 블록체인형 프로토콜을 기반으로 사용자 간 디지털 데이터의 안전한 저장과 전송을 위한 시스템에 관한 특허다.본 유럽 등록 특허(EP 388149)의 일 실시예에 따르면 사용자의 컴퓨팅 장치에 저장되거나 이와 통신하고 네트워크의 각 사용자와 연관된 개인 원장 데이터베이스(personal ledger database)를 포함한다.각 개인 원장 데이터베이스(personal ledger database)는 암호화 키로 연결된 블록으로 구성된다. 2명 이상의 검증된 사용자 간의 거래가 승인될 때 새로운 블록이 2명 이상의 검증된 사용자 각각과 연관된 개인 데이터베이스에 추가된다.상기 새로운 블록은 거래의 디지털 정보 중 적어도 일부를 저장하며 적어도 하나의 디지털 저장소의 디지털 주소를 기록한다.
-
미국, 30억 달러 투자로 최첨단 반도체 패키징 생태계 구축볼티모어에서 열린 행정부 발표에서 바이든-해리스 행정부는 최첨단 반도체 제조의 핵심 기술인 첨단 패키징 분야에 대한 미국의 역량을 강화하겠다는 새로운 비전을 공개했다. 이 발표는 Morgan State University에서 열린 행사에서 Laurie E 미국 상무부 장관 겸 NIST(National Institute of Standards and Technology) 국장의 발언으로 전해졌다. 로카시오 국장은 미국 상무부의 CHIPs 프로그램을 설명하며, 약 30억 달러 규모의 자금이 국가 고급 패키징 제조 프로그램을 지원하는 데 사용될 것이라고 밝혔다. 이 프로그램은 대통령의 미국 투자 계획의 일환으로, 혁신을 촉진하고 미국을 반도체 제조 분야의 선두주자로 만드는 데 기여할 것으로 기대된다. 로라 와이스 CHIPS 연구개발 책임자는 "미국이 10년 안에 세계에서 가장 정교한 칩을 제조하고 패키징 할 것을 상상하고 있다"고 말했다. NIST 책임자로리 E 로카시오는 "이는 자립적이고 수익성이 높으며 환경적으로 건전한 대량의 고급 패키징 산업을 후원하고, 시장 자립성을 가속화하기 위한 연구를 수행하는 것”이라고 덧붙였다. 이번 프로그램은 세계에서 가장 발전된 기술을 갖춘 반도체 제조 시설을 구축하고 미국의 기술 리더십과 경제 안보를 강화하기 위한 것이다. 약 30억 달러 규모의 자금이 새로운 기술 검증, 미국 고급 패키징 파일럿 시설, 인력 교육 프로그램, 재료, 장비, 도구 및 프로세스, 칩셋 생태계, 테스트 및 신뢰성 등에 사용될 예정이다. 이러한 프로그램은 NAPMP(National Advanced Packaging Manufacturing Program)의 일환으로, 미국의 고급 패키징 기술 개발을 지원하여 미국이 반도체 생태계에서 선두를 유지하고 유관 기업들을 유치하는 데 기여할 것으로 기대된다.
-
[특집-ISO/IEC JTC 1/SC 17 활동] ⑧Liaison document from CEN/CLC JTC 13: Cyber Security and Data Protection presentation 소개지난 10월16일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Liaison document from CEN/CLC JTC 13: Cyber Security and Data Protection presentation' 관련 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안 장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서는 'Liaison document from CEN/CLC JTC 13: Cyber Security and Data Protection presentation는 10월9일 생성된 문서의 네번째 수정판(v.0.4)이다.유럽표준화기구(European Standardization Organizations) CEN/CLC/JTC 13 사이버보안 및 데이터 보호(Cyber Security and Data Protection)에 대한 문서다.개요(Overview)는 1. General, 2. Scope, 3. Structure, 4. Working Groups, 5. Further Information 등으로 구성됐다. 1. General 파트는 다음과 같이 구성됐다.△CEN/CLC/JTC 13 Cybersecurity and Data Protection - Joint Technical Committee (JTC) of CEN and CENELEC - established November 2017△120+ European experts on Cybersecurity and Data Protection△7 dedicated Working Groups△3 Plenary Meetings/Sessions per Year△Annual Outreach Events△Chairperson: Walter Fumy, Bundesdruckerei (Germany)△Secretariat: DIN German Institute of Standardization (Germany)△Secretary: Martin Uhlherr (DIN)△CEN-CENELEC Management Centre Program Manager: Laurens Hernalsteen 2. Scope 파트는 다음과 같다.△Development of horizontal Standards in the Field of Cybersecurity and Data Protection for vertical Applications Domains△Horizontal Security & Privacy Topics of the evolving interconnected Society, driven by the European Market in Domains such as ICT, eHealth, Transport, Smart Cities, Automotive, IOT△Key Issues - Management Systems, Frameworks, Methodologies - Data Protection and Privacy - Services and Products Evaluation Standards suitable for Security Assessment for large Companies and small and medium Enterprises - Competence Requirements for Cybersecurity and Data Protection - Security Requirements, Services, Techniques and Guidelines for ICT Systems, Services, Networks and Devices, including Smart Objects and distributed Computing Devices△Identification and Adoption of published Documents by ISO/IEC JTC 1, other SDOs, international Bodies and industrial Fora△Development of CEN/CENELEC Publications for safeguarding Information - 이하 생략 -