검색결과
-
[특집-기술위원회] TC 224 식수, 폐수, 빗물 시스템 및 서비스(Drinking water, wastewater and stormwater systems and services)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 등도 포함된다.그리고 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 △1996년 TC 213, TC 214 △1998년 TC 215~218 △1999년 TC 219, TC 220 △2000년 TC 221. TC 222 등이 있다.ISO/TC 224 식수, 폐수, 빗물 시스템 및 서비스(Drinking water, wastewater and stormwater systems and services)과 관련된 기술위원회는 2001년 결성됐다. 사무국은 프랑스 표준화기구(Association Française de Normalization, AFNOR)에서 맡고 있다.위원회는 아르노 고드리에(M Arnaud Gaudrier)가 책임지고 있다. 현재 의장은 이자벨 벤듀브르(Mme Isabelle Vendeuvre)로 임기는 2025년까지다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi)이며 ISO 편집 관리자는 발레리아 아가넨노네(Ms Valeria Agamennone)다.범위는 식수 공급, 폐수 및 빗물 시스템과 관련된 서비스 활동과 프로세스에 관한 관리 개념의 표준화다. 구조에는 물 공급, 폐수 및 우수 시스템의 목적을 달성하는 데 필요한 활동이 포함된다. 식수 이외의 목적으로 물을 공급하는 것도 이 관리 개념 구조에 포함될 수 있다.단, △서비스 품질 기준에 대한 규범적 목표 또는 임계값 △식수 품질 또는 폐수 및 우수 환경 배출에 대한 허용 기준의 규범적 한계 △물 및 폐수 처리를 위한 화학적 및 생물학적 첨가제의 제품 사양 △ISO/TC 275의 범위 내에서 슬러지 회수, 재활용, 처리 및 폐기의 표준화 △ISO/TC 282의 범위 내에서 물 재사용 표준화 △ISO/TC 147에 포함된 수질 측정 방법 등은 제외한다.현재 ISO/TC 224 사무국의 직접적인 책임 하에 발행된 표준은 30개며 ISO/TC 224 사무국의 직접적인 책임 하에 개발 중인 표준은 11개다. 참여하고 있는 회원은 37개국, 참관 회원은 36개국이다.□ ISO/TC 224 사무국의 직접적인 책임 하에 발행된 표준 30개중 15개 목록▷ISO 24510:2024 Activities relating to drinking water and wastewater services — Guidelines for the assessment and for the improvement of the service to users▷ISO 24511:2024 Activities relating to drinking water and wastewater services — Guidelines for the management of wastewater utilities and for the assessment of wastewater services▷ISO 24512:2024 Activities relating to drinking water and wastewater services — Guidelines for the management of drinking water utilities and for the assessment of drinking water services▷ISO 24513:2019 Service activities relating to drinking water supply, wastewater and stormwater systems — Vocabulary▷ISO/TR 24514:2018 Activities relating to drinking water and wastewater services — Examples of the use of performance indicators using ISO 24510, ISO 24511 and ISO 24512 and related methodologies▷ISO 24516-1:2016 Guidelines for the management of assets of water supply and wastewater systems — Part 1: Drinking water distribution networks▷ISO 24516-2:2019 Guidelines for the management of assets of water supply and wastewater systems — Part 2: Waterworks▷ISO 24516-3:2017 Guidelines for the management of assets of water supply and wastewater systems — Part 3: Wastewater collection networks▷ISO 24516-4:2019 Guidelines for the management of assets of water supply and wastewater systems — Part 4: Wastewater treatment plants, sludge treatment facilities, pumping stations, retention and detention facilities▷ISO 24518:2015 Activities relating to drinking water and wastewater services — Crisis management of water utilities▷ISO/TS 24519:2022 Service activities relating to drinking water supply, wastewater and stormwater systems — Water and wastewater services for temporary settlements for displaced persons▷ISO/TS 24520:2017 Service activities relating to drinking water supply systems and wastewater systems — Crisis management — Good practice for technical aspects▷ISO 24521:2016 Activities relating to drinking water and wastewater services — Guidelines for the management of basic on-site domestic wastewater services▷ISO/TS 24522:2019 Event detection process: Guidelines for water and wastewater utilities▷ISO 24523:2017 Service activities relating to drinking water supply systems and wastewater systems — Guidelines for benchmarking of water utilities□ ISO/TC 224 사무국의 직접적인 책임 하에 개발중인 표준 11개 목록▷ISO/CD 18671 Method for determining products suitable to be flushed down a domestic toilet and establishment of appropriate labelling requirements.▷ISO 24516-1:2016/CD Amd 1 Guidelines for the management of assets of water supply and wastewater systems — Part 1: Drinking water distribution networks — Amendment 1▷ISO/DIS 24521 Drinking water, wastewater and stormwater systems and services — Guidelines for the management of basic on-site domestic wastewater services▷ISO/FDIS 24566-2 Drinking water, wastewater and storm water systems and services — Adaptation of water services to climate change impacts — Part 2: Stormwater services▷ISO/DIS 24566-3 Drinking water, wastewater and storm water systems and services — Adaptation of water services to climate change impacts — Part 3: Drinking Water services▷ISO/DIS 24566-4 Drinking water, wastewater and storm water systems and services — Adaptation of water services to climate change impacts — Part 4: Wastewater services▷ISO/CD TR 24589-1 Examples of good practice for the management of assets of water supply and wastewater systems — Part 1: Part 1: Water supply▷ISO/CD TR 24589-2 Examples of good practice for the management of assets of water supply and wastewater systems — Part 2: Part 2: Wastewater systems▷ISO/WD TS 24593 Establishment of a master plan for water supply – Evaluation of water demand▷ISO/AWI TR 24594 Service activities relating to drinking water supply, wastewater and stormwater systems — Water loss management good practice▷ISO/CD 24599 Guidelines for the management of mobile toilets under epidemic situations
-
과기정통부, 세계 최초 첨단 항공교통(AAM) 국제 사실표준화기구 첨단 항공교통 국제연합(G3AM) 출범과학기술정보통신부(이종호 장관, 이하 ‘과기정통부’)에 따르면 지난 5월14일(화) 세계 최초 첨단 항공교통(Advanced Air Mobility, 이하 AAM) 분야 국제 사실표준화 기구 G3AM(Global Association for Advanced Air Mobility) 출범식이 개최됐다.이날 출범식은 과기정통부가 주최하고 G3AM(사무국: 한국무인이동체연구조합(이하 KRAUV)) 주관, 한국정보통신기술협회(이하 TTA) 후원으로 서울 롯데월드타워 Sky31 컨퍼런스 홀에서 개최됐다.G3AM은 국내 전문가가 주도적으로 설립한 국제 사실표준화 기구다. △정보 공유체계 △교통관리 및 운항통제 △필수 항행 성능 등 여러 분야에서 새로운 표준을 개발·유지·관리하고 상호운용성과 호환성을 보장하는 사실표준화를 추진하기 위해서다.G3AM 창립회원은 대한항공, 인천국제공항공사, 파인브이티로보틱스, 한화시스템, 한국공항공사, 현대자동차 이동통신3사 등 AAM 관련 핵심 국내 기업 63개사가 참여했다.또한 Onesky(美), Skyports(英), Padinagroup(美), ANRA Technologies(美) 등 AAM 분야 다국적 기업이 참여했으며 Joby Aviation(美), Volocopter(獨) 등 다국적 기업들도 G3AM 회원가입을 검토 중이다. 첨단 항공교통(Advanced Air Mobility, 이하 AAM)은 단거리 중심의 도심항공교통(Urban Air Mobility, 이하 UAM)과 중·장거리 중심의 지역 간 항공교통(Regional Air Mobility, 이하 RAM)을 포괄하는 항공교통을 의미한다.AAM은 교통권 확대, 기존 교통수단의 환경 문제 해소 등 차원에서 미래형 교통수단으로 주목받고 있는 기술이다.따라서 AAM은 인공지능(AI), 이동통신, 데이터 등 다양한 디지털 기술이 적용되므로 상호운용성·신뢰성·지속가능성 등을 위한 국제표준을 확보하는 것이 중요하다. AAM 생태계 관련 산업은 아직 태동기 단계로 국제 표준화 주도권 선점의 적기로 평가받고 있다.출범식 기조연설에서 국제표준화기구 무인항공기시스템(ISO/TC20/SC16 Unmanned aircraft systems) 의장인 존스컬 워커가 'AAM을 지원하기 위한 국제기구의 역할'에 대해 발표했다.출범 기념 컨퍼런스는 △한국형 도심항공교통(K-UAM) 실증 성공사례(대한항공) △차세대 전기추진 수직 이착륙 비행체(eVTOL) 및 미래 항공 기체(AAV)(한화시스템, 한국항공우주산업) △AAM 사업 추진 동향(SKT, KT, LGU+등 이동통신 3사) 등으로 구성됐다.버티포트 인프라 개발현황은 2023년 G3AM의 회원으로 가입한 버티포트 분야 세계선도기업 Skyports가 맡았다.과기정통부 전영수 국장은 “첨단항공교통 분야는 디지털 기술 표준을 통해 우리나라가 주도권을 확보할 수 있는 영역”이라며 “G3AM이 국제적으로 인정받는 사실표준화기구로 자리 잡아 첨단항공교통 기술 발전과 생태계 조성에 중추적인 역할을 담당할 수 있도록 지원하겠다”고 말했다.참고로 전기추진 수직 이착륙 비행체(electric Vertical Take-Off and Landing, eVTOL)란 전기를 사용해 활주로 없이 공중에 떠오르는 비행체를 말한다.미래항공 기체(Advanced Air Vehicle)란 자율비행과 하이브리드 전기추진으로 장시간 비행 가능한 비행체를 뜻하며 버티포트(VertiPort)란 수직 비행(Vertical Flight)과 항구(Port)의 합성어로 기체가 수직 이착륙할 수 있는 공간이다.사실 표준(事實標準, de facto standard)이란 한국정보통신기술협회(TTA) 정보통신용어사전에 시장에서 표준으로 인정받거나 필요에 따라 업계를 중심으로 결성된 사실 표준화기구에서 제정되는 표준을 말한다.마이크로소프트의 윈도(Microsoft Windows)가 대표적인 예로 사실 표준은 강제 사항이 아니지만 업계에서 대부분 이 표준을 준수하고 있다.완성된 사실 표준은 필요하면 공신력 있는 국제 또는 국가 표준화 기구에서 일정한 절차와 심의를 걸쳐 공식 표준(de jure standard)으로 제정되는 경우도 있다. 하지만 대부분은 시장의 필요가 적어질 경우 자연스럽게 도태된다.미국 전기전자협회(IEEE), 인터넷 엔지니어링 태스크 포스(IETF), 월드와이드웹 컨소시엄(W3C) 등이 사실 표준화 기구다.
-
[특집-ISO/IEC JTC 1/SC 17 활동] 35. Result of voting on SR Ballot for ISO/IEC 7811-7(N 7345)2023년 12월04일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Result of voting on SR ballot for ISO/IEC 7811-7(N 7345)' 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서인 'Result of voting on SR ballot for ISO/IEC 7811-7'은 ISO/IEC 7811-7:2018 (Ed 3)(restricted access)와 관련한 투표결과를 포함하고 있다.ISO/IEC 7811-7:2018 (Ed 3)(restricted access)는 Identification cards — Recording technique — Part 7: Magnetic stripe: High coercivity, high density에 관한 것이다.N 7345 문서는 N 7338, N 7339, N 7340, N 7341, N 7342, N 7343, N 7344 문서와 마찬가지로 2023년 7월15일~12월2일 동안 투표가 진행됐다. 기간 내 각 회원국들은 안건에 대해 의사를 표명했다.투표 항목은 △Confirm △Revise/Amend △Withdraw △Abstain lack of consensus △Abstain lack of national expert input △Stabilize △Q.2 △Q.3 △Q.4 △Q.5 △Q.6 등 총 11개다. 구체적인 질문 내용은 다음과 같다.▷ Q.1 Recommended action▷ Q.2 Has this International Standard been adopted or is it intended to be adopted in the future as a national standard or other publication?▷ Q.3 Is the national publication identical to the International Standard or was it modified?▷ Q.4 If this International Standard has not been nationally adopted, is it applied or used in your country without national adoption or are products/processes/services used in your country based on this standard?▷ Q.5 Is this International Standard, or its national adoption, referenced in regulations in your country?▷ Q.6 If the committee decides to revise or amend, do you propose an expert and/or project leader for the development of that project?참고로 11개 항목 중 투표 결과를 살펴보면 △Confirm 12개국 △Revise/Amend 1개국 △Abstain lack of national expert input 22개국 등으로 나타났다.- 이하 생략 -
-
[특집-ISO/IEC JTC 1/SC 17 활동] 34. Result of voting on SR ballot for ISO/IEC 7811-6(N 7344)2023년 12월04일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Result of voting on SR ballot for ISO/IEC 7811-6(N 7344)' 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서인 'Result of voting on SR ballot for ISO/IEC 7811-6'은 ISO/IEC 7811-6:2018 (Ed 5)(restricted access)와 관련한 투표결과를 포함하고 있다.ISO/IEC 7811-6:2018 (Ed 5)(restricted access)는 Identification cards — Recording technique — Part 6: Magnetic stripe: High coercivity에 관한 것이다.N 7344 문서는 N 7338, N 7339, N 7340, N 7341, N 7342, N 7343 문서와 마찬가지로 2023년 7월15일~12월2일 동안 투표가 진행됐다. 기간 내 각 회원국들은 안건에 대해 의사를 표명했다.투표 항목은 △Confirm △Revise/Amend △Withdraw △Abstain lack of consensus △Abstain lack of national expert input △Stabilize △Q.2 △Q.3 △Q.4 △Q.5 △Q.6 등 총 11개다. 구체적인 질문 내용은 다음과 같다.▷ Q.1 Recommended action▷ Q.2 Has this International Standard been adopted or is it intended to be adopted in the future as a national standard or other publication?▷ Q.3 Is the national publication identical to the International Standard or was it modified?▷ Q.4 If this International Standard has not been nationally adopted, is it applied or used in your country without national adoption or are products/processes/services used in your country based on this standard?▷ Q.5 Is this International Standard, or its national adoption, referenced in regulations in your country?▷ Q.6 If the committee decides to revise or amend, do you propose an expert and/or project leader for the development of that project?참고로 11개 항목 중 투표 결과를 살펴보면 △Confirm 11개국 △Revise/Amend 1개국 △Abstain lack of national expert input 23개국 등으로 나타났다.- 이하 생략 -
-
[특집-ISO/IEC JTC 1/SC 17 활동] 33. Result of voting on SR ballot for ISO/IEC 7811-2(N 7343)2023년 12월04일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Result of voting on SR ballot for ISO/IEC 7811-2(N 7343)' 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서인 'Result of voting on SR ballot for ISO/IEC 7811-2'는 ISO/IEC 7811-2:2018 (Ed 5)(restricted access)와 관련한 투표결과를 포함하고 있다. ISO/IEC 7811-2:2018 (Ed 5)(restricted access)는 Identification cards — Recording technique — Part 2: Magnetic stripe: Low coercivity에 관한 것이다. N 7343 문서는 N 7338, N 7339, N 7340, N 7341, N 7342 문서와 마찬가지로 2023년 7월15일~12월2일 동안 투표가 진행됐다. 기간 내 각 회원국들은 안건에 대해 의사를 표명했다.투표 항목은 △Confirm △Revise/Amend △Withdraw △Abstain lack of consensus △Abstain lack of national expert input △Stabilize △Q.2 △Q.3 △Q.4 △Q.5 △Q.6 등 총 11개다. 구체적인 질문 내용은 다음과 같다.▷ Q.1 Recommended action▷ Q.2 Has this International Standard been adopted or is it intended to be adopted in the future as a national standard or other publication?▷ Q.3 Is the national publication identical to the International Standard or was it modified?▷ Q.4 If this International Standard has not been nationally adopted, is it applied or used in your country without national adoption or are products/processes/services used in your country based on this standard?▷ Q.5 Is this International Standard, or its national adoption, referenced in regulations in your country?▷ Q.6 If the committee decides to revise or amend, do you propose an expert and/or project leader for the development of that project?참고로 11개 항목 중 투표 결과를 살펴보면 △Confirm 12개국 △Revise/Amend 1개국 △Abstain lack of consensus 1개국 △Abstain lack of national expert input 21개국 등으로 나타났다. - 이하 생략 -
-
[특집-ISO/IEC JTC 1/SC 17 활동] 32. Result of voting on SR Ballot for ISO/IEC 7811-1(N 7342)2023년 12월04일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Result of voting on SR Ballot for ISO/IEC 7811-1(N 7342)' 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서인 'Result of voting on SR Ballot for ISO/IEC 7811-1'는 ISO/IEC 7811-1:2018 (Ed 5)(restricted access)와 관련한 투표결과를 포함하고 있다. ISO/IEC 7811-1:2018 (Ed 5)(restricted access)는 Identification cards — Recording technique — Part 1: Embossing에 관한 것이다. N 7342 문서는 N 7338, N 7339, N 7340, N 7341 문서와 마찬가지로 2023년 7월15일~12월2일 동안 투표가 진행됐다. 기간 내 각 회원국들은 안건에 대해 의사를 표명했다.투표 항목은 △Confirm △Revise/Amend △Withdraw △Abstain lack of consensus △Abstain lack of national expert input △Stabilize △Q.2 △Q.3 △Q.4 △Q.5 △Q.6 등 총 11개다. 구체적인 질문 내용은 다음과 같다.▷ Q.1 Recommended action▷ Q.2 Has this International Standard been adopted or is it intended to be adopted in the future as a national standard or other publication?▷ Q.3 Is the national publication identical to the International Standard or was it modified?▷ Q.4 If this International Standard has not been nationally adopted, is it applied or used in your country without national adoption or are products/processes/services used in your country based on this standard?▷ Q.5 Is this International Standard, or its national adoption, referenced in regulations in your country?▷ Q.6 If the committee decides to revise or amend, do you propose an expert and/or project leader for the development of that project?참고로 11개 항목 중 투표 결과를 살펴보면 △Confirm 12개국 △Revise/Amend 1개국 △Abstain lack of consensus 1개국 △Abstain lack of national expert input 21개국 등으로 나타났다. - 이하 생략 -
-
[특집-ISO/IEC JTC 1/SC 17 활동] 31. Result of voting on SR Ballot for ISO/IEC 18745-1(N 7341)2023년 12월04일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Result of voting on SR Ballot for ISO/IEC 18013-1(N 7340)' 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다.배포된 문서인 'Result of voting on SR Ballot for ISO/IEC 18745-1'는 ISO/IEC 18745-1:2018 (Ed 2)(restricted access)와 관련한 투표결과를 포함하고 있다. ISO/IEC 18745-1:2018 (Ed 2)(restricted access)는 Test methods for machine readable travel documents (MRTD) and associated devices — Part 1: Physical test methods for passport books (durability)에 관한 것이다. N 7341 문서는 N 7338, N 7339, N 7340 문서와 마찬가지로 2023년 7월15일~12월2일 동안 투표가 진행됐다. 기간 내 각 회원국들은 안건에 대해 의사를 표명했다.투표 항목은 △Confirm △Revise/Amend △Withdraw △Abstain lack of consensus △Abstain lack of national expert input △Stabilize △Q.2 △Q.3 △Q.4 △Q.5 △Q.6 등 총 11개다. 구체적인 질문 내용은 다음과 같다.▷ Q.1 Recommended action▷ Q.2 Has this International Standard been adopted or is it intended to be adopted in the future as a national standard or other publication?▷ Q.3 Is the national publication identical to the International Standard or was it modified?▷ Q.4 If this International Standard has not been nationally adopted, is it applied or used in your country without national adoption or are products/processes/services used in your country based on this standard?▷ Q.5 Is this International Standard, or its national adoption, referenced in regulations in your country?▷ Q.6 If the committee decides to revise or amend, do you propose an expert and/or project leader for the development of that project?참고로 11개 항목 중 투표 결과를 살펴보면 △Confirm 9개국 △Revise/Amend 4개국 △Abstain lack of national expert input 22개국 등으로 나타났다. - 이하 생략 -
-
[특집-기술위원회] TC 215 - 의료 정보학(Health informatics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 △1996년 TC 213, TC 214 등이 있다.ISO/TC 215 의료 정보학(Health informatics)과 관련된 기술위원회는 1998년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 레이첼 호손(Ms Rachel Hawthorne)가 책임지고 있다. 현재 의장은 토드 쿠퍼(Mr Todd Cooper)이며 임기는 2026년 말까지다. ISO 기술 프로그램 관리자는 마호 다카하시(Mme Maho Takahashi), ISO 편집 관리자는 발레리아 아가넨노네(Ms Valeria Agamennone) 등이다.범위는 의료 관련 데이터, 의료 시스템의 모든 측면을 지원하고 활성화하는 지식의 수집, 교환 및 사용을 촉진하기 위한 의료 정보학 분야의 표준화다.현재 ISO/TC 215 사무국과 관련해 발행된 표준은 237개며 ISO/TC 215 사무국의 직접적인 책임 하에 발행된 표준은 225개다.ISO/TC 215과 관련해 개발 중인 표준은 64개며 이중 ISO/TC 215 사무국의 직접적인 책임 하에 개발 중인 표준은 62개다. 참여하고 있는 회원은 35개국, 참관 회원은 32개국이다.□ ISO/TC 215 사무국의 직접적인 책임 하에 발행된 표준 225개 중 15개 목록▷ISO 1828:2012 Health informatics — Categorial structure for terminological systems of surgical procedures▷ISO/TR 4421:2023 Health informatics — Introduction to Ayurveda informatics▷ISO/TS 5044:2023 Health informatics — Information model for quality control of traditional Chinese medicinal products▷ISO/TS 5118:2022 Health informatics — Categorial structure of representation for evaluation of clinical practice guidelines of traditional Chinese medicine▷ISO/TS 5346:2022 Health informatics — Categorial structure for representation of traditional Chinese medicine clinical decision support system▷ISO 5477:2023 Health informatics — Interoperability of public health emergency preparedness and response information systems▷ISO/TS 5499:2024 Health informatics — Clinical particulars — Core principles for the harmonization of therapeutic indications terms and identifiers▷ISO/TS 5568:2022 Health informatics — Traditional Chinese medicine — Labelling metadata of human biological sample information▷ISO/TS 5569:2023 Health informatics — Conceptual data model for Chinese medicinal herbs▷ISO/TR 9143:2023 Health informatics — Sex and gender in electronic health records▷ISO 10159:2011 Health informatics — Messages and communication — Web access reference manifest▷ISO 10781:2023 Health informatics — HL7 Electronic Health Record-System Functional Model, Release 2.1 (EHR FM)▷ISO/IEEE 11073-00103:2015 Health informatics — Personal health device communication — Part 00103: Overview▷ISO/IEEE 11073-10101:2020 Health informatics — Device interoperability — Part 10101: Point-of-care medical device communication — Nomenclature▷ISO/IEEE 11073-10102:2014 Health informatics — Point-of-care medical device communication — Part 10102: Nomenclature — Annotated ECG□ ISO/TC 215 사무국의 직접적인 책임 하에 개발 중인 표준 62개 중 15개 목록▷ISO/AWI TR 4419 Health informatics — Reducing clinicians burden▷ISO/DTS 5384 Health informatics - Categorial Structure and Data Elements for the Identification and Exchange of Immunization Data▷ISO/CD TS 5615 Health informatics — Accelerating Safe, Effective and Secure Remote Connected Care and Mobile Health Through Standards-Based Interoperability Solutions Addressing Gaps Revealed by Pandemics▷ISO/DTS 5777 Health informatics — The architecture of internet healthcare service network▷ISO/DTS 5788 Health informatics — Internet healthcare service pattern▷ISO/CD TS 6201.2 Health Informatics — Personalized Digital Health -Framework▷ISO/CD TS 6204 Health Informatics — Categorial structures for representation of Ayurvedic medicinal water — Decocting process in Ayurveda▷ISO/AWI TS 6226 Health informatics — Reference architecture for syndromic surveillance systems for infectious diseases▷ISO/DTR 6231 Health informatics — Standardizing graphical content▷ISO/CD TS 6268-1 Health informatics — Cybersecurity framework for telehealth environments — Part 1: Overview and Concepts▷ISO/AWI TS 6268-2 Health informatics — Cybersecurity framework for telehealth environments — Part 2: Cybersecurity reference models of telehealth▷ISO/CD TS 7122 Health Informatics — Guidelines for exchanging data generated by POCT (Point of Care Testing) devices between screening center and clinical laboratory▷ISO/AWI TS 9166 Health Informatics — Guidelines for self-assessment questionnaire systems▷ISO/DTS 9320 Health informatics — Standardized data set for transfer of hemodialysis patients▷ISO/DTS 9321 Health informatics — General requirements of multi-centre medical data collaborative analysis□ ISO/TC 215 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 215/SC 1 Genomics Informatics ; 발행된 표준 12개, 개발 중인 표준 2개
-
[특집-기술위원회] TC 214 - 승강기 작업 플랫폼(Elevating work platforms)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 등이 있다.ISO/TC 214 승강기 작업 플랫폼(Elevating work platforms)과 관련된 기술위원회는 TC 213과 마찬가지로 1996년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 샐리 사이츠(Ms Sally Seitz)가 책임지고 있다. 현재 의장은 스티븐 A. 베스트(Mr Stephen A. Best)이며 임기는 2029년 말까지다. ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 앤 기엣(Ms Anne Guiet) 등이다.범위는 용어, 등급, 일반 원칙(기술적 성능 요구 사항 및 위험 평가), 안전 요구사항, 테스트 방법, 유지관리, 승강에 사용되는 작업 플랫폼을 올리기 위한 조작 등의 표준화다. 또한 작업을 수행할 작업 위치에 직원(및 관련 작업 도구, 자재 등)을 배치에 대한 표준화도 포함된다.현재 ISO/TC 214 사무국의 직접적인 책임 하에 발행된 표준은 9개며 ISO/TC 214 사무국의 직접적인 책임 하에 개발 중인 표준은 3개다. 참여하고 있는 회원은 19개국, 참관 회원은 19개국이다.□ ISO/TC 214 사무국의 직접적인 책임 하에 발행된 표준 9개 목록▷ISO 16368:2010 Mobile elevating work platforms — Design, calculations, safety requirements and test methods▷ISO 16369:2007 Elevating work platforms — Mast-climbing work platforms▷ISO 16653-1:2008 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 1: MEWPs with retractable guardrail systems▷ISO 16653-2:2021 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 2: MEWPs with non-conductive (insulating) components▷ISO 16653-3:2011 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 3: MEWPs for orchard operations▷ISO 18878:2013 Mobile elevating work platforms — Operator (driver) training▷ISO 18893:2014 Mobile elevating work platforms — Safety principles, inspection, maintenance and operation▷ISO 20381:2009 Mobile elevating work platforms — Symbols for operator controls and other displays▷ISO 21455:2020 Mobile elevating work platforms — Operator's controls — Actuation, displacement, location and method of operation□ ISO/TC 214 사무국의 직접적인 책임 하에 개발 중인 표준 3개 목록▷ISO/FDIS 16368 Mobile elevating work platforms — Design, calculations, safety requirements and test methods▷ISO/DIS 18878 Mobile elevating work platforms — Operator (driver) training▷ISO/DIS 18893 Mobile elevating work platforms — Safety principles, inspection, maintenance and operation
-
[특집-기술위원회] TC 213 - 치수와 기하학적 제품의 사양 및 검증(Dimensional and geometrical product specifications and verification)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 등이 있다.ISO/TC 213 치수와 기하학적 제품의 사양 및 검증(Dimensional and geometrical product specifications and verification)과 관련된 기술위원회는 1996년 결성됐다. 사무국은 영국 표준협회(British Standards Institution, BSI)에서 맡고 있다.위원회는사라 켈리(Miss Sarah Kelly)가 책임지고 있다. 현재 의장은 이안 맥클라우드(Mr Iain Macleod)이며 임기는 2025년말까지다. ISO 기술 프로그램 관리자는 이사벨 베가(Ms Isabelle Vega), ISO 편집 관리자는 니콜라 페루(Ms Nicola Perou) 등이다.범위는 기하학적 제품 사양(GPS) 분야의 표준화다. 즉 치수 및 기하학적 공차, 표면 특성 및 관련 검증 원리, 치수 및 기하학적 측정의 불확실성을 포함한 측정 장비 및 교정 요구 사항을 다루는 거시 및 미세 형상 사양이다.표준화에는 기본 레이아웃과 도면 표시(기호)에 대한 설명이 포함된다. 단, 도면 표시(기호)의 특정 비율 및 치수 정의, 실행은 제외된다.현재 ISO/TC 213 사무국의 직접적인 책임 하에 발행된 표준은 147개며 ISO/TC 213 사무국의 직접적인 책임 하에 개발 중인 표준은 22개다. 참여하고 있는 회원은 26개국, 참관 회원은 25개국이다.□ ISO/TC 213 사무국의 직접적인 책임 하에 발행된 표준 147개 중 15개 목록▷ISO 1:2022 Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties▷ISO 286-1:2010 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits▷ISO 286-1:2010/Cor 1:2013 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits — Technical Corrigendum 1▷ISO 286-2:2010 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts▷ISO 286-2:2010/Cor 1:2013 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts — Technical Corrigendum 1▷ISO 463:2006 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges▷ISO 463:2006/Cor 1:2007 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 1▷ISO 463:2006/Cor 2:2009 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 2▷ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out▷ISO 1119:2011 Geometrical product specifications (GPS) — Series of conical tapers and taper angles▷ISO 1660:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing▷ISO 1938-1:2015 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size▷ISO 1938-2:2017 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Reference disk gauges▷ISO 2538-1:2014 Geometrical product specifications (GPS) — Wedges — Part 1: Series of angles and slopes▷ISO 2538-2:2014 Geometrical product specifications (GPS) — Wedges — Part 2: Dimensioning and tolerancing□ ISO/TC 213 사무국의 직접적인 책임 하에 개발 중인 표준 22개 중 15개 목록▷ISO/CD 1938-1 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size▷ISO/AWI 2768 General tolerances▷ISO/DIS 5059-1 Geometrical product specifications (GPS) — Dimensional measuring equipment: inside micrometers — Part 1: Two-point inside micrometers — Design and metrological characteristics▷ISO/FDIS 5459 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems▷ISO/DIS 5463 Geometrical product specifications (GPS) — Form measuring equipment; Rotary axis form measuring instruments — Design and metrological characteristics▷ISO/CD 10360-102 Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 102: The language of symbols G3▷ISO/AWI 12179 Geometrical product specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments▷ISO/DIS 14405-1 Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes▷ISO/CD TS 15530-2 Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 2: Part 2: Evaluating task-specific measurement uncertainty by multiple measurement strategies using a single uncalibrated workpiece▷ISO/DIS 16610-21 Geometrical product specifications (GPS) — Filtration — Part 21: Linear profile filters: Gaussian filters▷ISO/CD 16610-22 Geometrical product specifications (GPS) — Filtration — Part 22: Linear profile filters: Spline filters▷ISO/DIS 16610-31 Geometrical product specifications (GPS) — Filtration — Part 31: Robust profile filters: Gaussian regression filters▷ISO/DIS 16610-45 Geometrical product specifications (GPS) — Filtration — Part 45: Morphological profile filters: Segmentation▷ISO 18183-1 Geometrical product specifications (GPS) — Partition — Part 1: Vocabulary and basic concepts▷ISO/CD TR 23850 Geometrical product specifications (GPS) — Association — Mathematical concepts